1 / 6
Vial Drawing Assist fits all 0.5ml to 30ml+ Insulin / GLP-1 / TRT / Peptides — zdjęcie 1
1 / 6

Vial Drawing Assist fits all 0.5ml to 30ml+ Insulin / GLP-1 / TRT / Peptides

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Simplifies drawing medication into a syringe

Ocena
5 / 5
Polubienia
25
Pobrania
172
Wydruki
1
Wyświetlenia
1423
Oceny
2

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

What is it?

Built to pair with my "Magnetic Injection Assistant", this securely holds medication vials inline and at the correct depth while drawing your meds into a syringe.

How to use:

  1. Add your vial to the Carrier (now is also a good time to wipe the stopper of your vial with an alcohol wipe to sanitize it)

  2. Add the cap.  It twists on with a ~1/4 turn

  3. Add your syringe to the Injection Assistant and leave the sled in the 'up' position

  4. Attach the attached Drawing Assist to the bottom of the Injection Assistant (they should snap together)

  5. Push the plunger to lower the syringe to the 'down' position, which will insert the needle into the vial

  6. Flip the whole thing upside-down and draw your medication

  7. Slide the Injection assistant sled back to the 'up' position

  8. Remove the Drawing Assist from the bottom

  9. You're done!  Use the Injection Assistant as normal

Selecting the right sizes:

Glass vials generally tend to be one of a handful of common widths and use the same size crimped-on cap, but their height varies by provider.  

Needle length is also a factor because we want to needle to penetrate into the vial by only a few mm.  This ensures that we can fully draw all of the medication out of the vial when it's turned upside down.

Cap Sizing:

Select a cap size based on the length of the needles you use on your syringe.  Common sizes are:

  • 3/16" or 5mm

  • 15/64" or 6mm

  • 5/16" or 8mm

  • 1/2" or 12.7mm

  • 5/8" or 16mm

  • 1" or 25mm

  • 1.25" or 32mm

  • 1.5" or 38mm

The cap sizes are designed so for each size, the needle will insert only a few mm into the vial.  This helps to get the most medication out of a vial that is nearly empty.

Carrier Sizing:

Vial carriers are sized by the diameter and total height of your vials.  A printable sizing gauge is available in the print profiles if you don't have calipers to measure your vial

  1. Choose the print profile that matches the approximate width of your vial

  2. In that profile, choose the plate that matches the height of your vial

Broadly, most vials follow this rule of thumb:

  • 15mm:  0.5-1ml

  • 16mm:  1-3ml

  • 22mm:  5-10ml

  • 24mm:  10ml+

  • 30mm:  10-20ml

  • 34mm:  30ml+

     

Printing:

Print as oriented.  No supports needed.

If you already have one of the earlier Injection Assistants, they should work fine here as is, but a newer body is available which includes an additional magnet on the bottom for a more secure connection.  Files for those are available here if you want to print one.

*Note: the new body is now the default on the V2 Injection Assistant.  If you printed it recently, you probably already have it.

Assembly:

  1. Insert a 6x3 magnet into the bottom of your Injection Assistant body. (if you haven't already assembled that previously)

  2. Stick an extra magnet to the bottom of the Injection assistant, and use that to press the extra magnet into the top of the Vial Cap.  This makes it easier to insert the magnet and insures that both are in the correct orientation to attract one another.

  3. Add your vial to the Carrier (now is also a good time to wipe the stopper of your vial with an alcohol wipe to sanitize it)

  4. Add the cap.  It twists on with a ~1/4 turn

Note: The 24-34mm carriers load the vial from the bottom and include an additional ‘plug’ that threads on the underside of the carrier.

Tagi