1 / 5
qGATS: quad version of the GATS belt tensioning system for Ratrig Vcore 4 — zdjęcie 1
1 / 5

qGATS: quad version of the GATS belt tensioning system for Ratrig Vcore 4

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

qGATS: quad version of the GATS belt tensioning system for Ratrig Vcore 4

Ocena
5 / 5
Polubienia
10
Pobrania
36
Wydruki
1
Wyświetlenia
261
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Accessories
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This model is inspired by the excellent GATS system, https://www.printables.com/model/1165578-gravity-assisted-tensioning-system-gats-for-v-core.

I wanted a system that would tension all the four belts at the same time, and also add a few changes that make sense in my environment.

Features:

  • Tension all of the four belts of a hybrid/IDEX in a single go, as tensioning one belt affects the tension of other belts.

  • There are hooks for my weights to make the system easier to use.

  • Belts are aligned with the tensioner screws, so that friction would not affect the results.

  • The tensioner screw grabbers are "forced" to be correctly seated, and aligned laterally as well. 

  • Optimized for use with weight plates

    • Include an adjustment capsule to make weights equal

  • Possible to tension two belts with just a single weight per side

  • Possible to use 13mm or 12mm idlers

The belt grabbers are based on the Wedge-Lock design by @FBGDesign_302513 .With the dimensions used here for them,  you can use either a piece of filament as the wedge:

or you can fold the belt onto itself and use that as the wedge:

When using either method, push the wedge into the slot far enough while pulling the belt, to ensure that it engages correctly.

For the cantilevered idlers I used M5x45 as the shafts. Depending on the screw you use, you might need a spacer/washer to prevent the screwhead from touching the outer race of the idler. The "body side" of the idler has a printed collar for that purpose already.

For the "single weight system - idler adapter" that is supported at both ends I used M5x25. No spacers should be needed there.

The design assumes a 0.5mm offset from the face of the belt to the center of the load-bearing fibres in the belt. This seems to work relatively well also for the toothed side, as the teeth compress a bit under load. If you want to make the belts always ride smooth side to the idler, you can switch the orientation by using the grabber-twister. Or simply turn the belt, it probably does not cause major errors.

Here is an example of switching the orientation of the belt with the grabber-twister:

When using the 13mm idlers, line up the top guide with the top of the tensioner mount block. When using 12 mm idlers, line up the bottom guide with the bottom or the tensioner mount block. This lines up the body with the tensioner screws.

I use two 10kg weights for tensioning, one on each side. I make them equal in weight by using a filler capsule that fits into the 40mm hole of the plate. I used some M6 screws as the weight inside the capsule, but use whatever you have at hand:


The force from the 10kg plate gets divided to the two qGATS belts with the "single weight system - idler adapter":

(as you can see, the final attachment to the weight is a high-tech solution called a "string")

That 10kg-per-side setup gives a tension of 25N for each of the belts. You could also use 4x5kg weights to get the same 25N tension, but then you'd need 3 weight-equalizing capsules. 

The model has internal slots that are there to create walls to strengthen the structure. Make sure your slicer resolves these slots into walls and does not just treat them as solid:

This is starting to be some heavy stuff, literally. You do not want to drop the weights on your toes or anything that might break! I have in no way made sure that the structures are safe or usable or won't break. I've been using them for several months now, but that of course is no guarantee of anything. 

Tagi