1 / 2
MagDock — Magnetic Desk & Shop Organizer Family — zdjęcie 1
1 / 2

MagDock — Magnetic Desk & Shop Organizer Family

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A family of small organizers that embed neodymium discs in their backs, so they snap onto ANY ferrous surface

Ocena
0 / 5
Polubienia
0
Pobrania
4
Wydruki
0
Wyświetlenia
35
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Organizers
Licencja
Creative Commons — Attribution

MagDock is a small family of organizers that each carry neodymium discs sealed in their back, so they snap onto ANY ferrous surface: a 3D printer's sheet-steel frame or door, a fridge, filing cabinet, toolbox, server rack, washing machine, or radiator. No screws, no adhesive, no separate mounting plate — the magnets ARE the mount, which is what makes the whole family generic.

Parts

  • hook — slim half-circle crook for props, cables, keys, straps.

  • tray — shallow scoop bin (64 x 46 mm) for screws, nozzles, clips, small parts. Open front mouth with a small bottom lip and a tiny top eave-lip.

  • tray_tall — the same scoop bin made HALF as wide and TWICE as high (32 x 46 mm, 44 mm tall): a slim upright caddy for pens, brushes, or long bits standing on end.

  • pliers — a vertical three-wall square slot that catches pliers/scissors at the pivot. The closed jaws drop in; the wide box-joint can't pass, so the tool is captured (no slip, no roll-off like a hook). The hole runs through both faces so long jaws poke out the back.

  • slot — a slim 11 mm open-top twin-post cradle (no roof) for small flush-cutters / scissors.

  • plate — a bare puck: a stick-anything pad, or a base to build your own feature on.

hook, pliers, slot and plate share one round 36 mm puck base. tray and tray_tall use their own rectangular floor so nothing cantilevers. The magnet ring is symmetric, so just rotate any puck on the steel to point its feature the way you want (hook opening up, slot mouth up).

MAGNETS Default is Ø10 x 5 mm discs, 3 per accessory (roughly 8 kg of gross pull on steel — plenty in shear for a loaded hook). The light-duty parts (slot, tray_tall) instead use the small Ø5 x 3 mm discs, 4 per part. Everything is parametric — edit magnet_d / magnet_h / magnet_n at the top of the .scad, or pass them to build.sh.

The pockets are fully enclosed voids: the discs get sealed inside the part DURING printing, so there are no caps, no glue, and nothing to fall out. From the steel face outward the stack is: 1 mm skin (prints on the bed) / the magnet / 1 mm of sealing layers printed after the pause.

How To Print

embed the magnets mid-print Every part lies flat on its back, with NO supports. The back face (against the steel) prints on the bed, so it comes out dead flat for maximum magnet contact. Use 0.2 mm layers and at least 3 walls.

  1. Slice the part in Bambu Studio (or your slicer).

  2. Add a pause / "Insert Pause" at height z = mag_floor + magnet_h. The .scad echoes the exact height when you render. At a 0.2 mm layer height:

  • Big Ø10 x 5 parts (hook / tray / pliers / plate): pause at z = 6.0 mm (after layer 30).

  • Small Ø5 x 3 parts (slot / tray_tall): pause at z = 4.0 mm (after layer 20).

  1. At the pause the pockets are open at the top with their floor already printed under them. Drop one disc into each pocket. Keep the polarity consistent across a plate if you want the parts to share a keeper.

  2. Resume. The cover layers print straight onto the magnet faces, sealing them in with a flat finish and no bridging.

The big-magnet parts all share the same pause height, so one pause covers a whole mixed big-magnet plate. The small-magnet parts (slot, tray_tall) pause lower — keep them on their own plate.

PARAMETRIC Everything important is a variable at the top of magnetic_dock.scad: magnet size + count, puck diameter, wall thickness, tray dimensions, hook radius, slot gap, plier hole. Render a single part with, for example:

openscad -o tray.stl -D 'part="tray"' magnetic_dock.scad

The .scad source is attached so you can re-tune any of it to your magnets and tools.

The photos show the family printed in red PLA: the hook, the slot holding scissors, a wrench in the pliers slot, and the wide tray (its 4 floor magnets visible through the translucent floor) all snapped onto a steel rail.

Tagi