1 / 6
Mount for LilyGo T-RGB 2.1” Delonghi ECP — zdjęcie 1
1 / 6

Mount for LilyGo T-RGB 2.1” Delonghi ECP

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Front mount a LilyGo T-RGB 2.1” round touch screen display to a Delonghi ECP series espresso machine for GaggiMate.

Ocena
0 / 5
Polubienia
1
Pobrania
11
Wydruki
0
Wyświetlenia
124
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Gadgets
Licencja
Creative Commons — Attribution — Share Alike

This is intended to mount LilyGo T-RGB 2.1” round touch screen display to a Delonghi ECP series espresso machine for the purposes of providing a GaggiMate display.  There are other options out there, but they did hold the screen securely, weren’t intended for the Lilygo, and/or were paid models. 

I found a model by PotatoNuke that fit the LilyGo T-RGB 2.1 T-RGB PCB, but did not fit the screen, so this is a remix of that to fit the 2.1” screen, and to mount to a Delonghi ECP series espresso machine.

I would suggest printing the back mount out of PETG, or being careful with the clips when installing.  It doesn’t need to come in and out, so if you get it in successfully you are probably good to go.  This piece is very close to the boiler, so it could also have issues with heat.  I have not tried PLA for this, and I haven’t used my PETG version long enough to show any problems.  I printed the rest of the parts from PLA.

There are two “covers”.  Both are intended to friction fit on the base.  The short one allows access to the rts, while the tall ones covers up the entire base.  You only need one, but I used both.  I used the short one until everything was done and the firmware was installed, then swapped the tall one when it was complete.

Installation

Back Piece

Insert the back piece in from the inside of the ECP case top and click it into place.  It recommended that you do a test fit of the screws to this back piece while securely holding it.  This way it can cut some threads and less pressure is required for final installation. 

Screen Assembly

The LilyGo screen is somewhat fragile as the PCB and LCD are only attached by a flexible ribbon cable.  There should be double faced tape on the PCB to allow it to be secured to the LCD.  I am ashamed I didn’t know this until after I was done with my install.  I suggest to make sure alignment is accurate that your print and test fit the base and the top.  Once that is good, place the PCB in the base, then remove the protective strip from the 3 pieces of tape, and carefully align the screen to the base and press gently against the PCB.  This will ensure accurate alignment.

If you are installing the original top screws into the ECP top, then you must first install the ECP top, then install the 2 screws on the top, then install the front plate.  Once you have done that you can install the Base to the ECP front panel.   I suggest skipping the 2 top screws, and assembling the front panel to the top piece, and then mounting the base to the top/front panel before completing along with the mount prior to installing on the ECP.  

Base

Once the ECP top and front plate are assembled, you can attach the base.  First place the spacer over the back piece clips and then place the base against the spacer while aligning the screw holes.  Use the original screws to attach the base being careful not to press too hard. There is some room to adjust the display left/right, but initially center the display before tightening them completely.  

Final Assembly

There is a channel for the power connector to fit, and route through the middle of the mount.  Keep in mind this cable will also be close to the boiler, so careful routing and use of silicone wires is recommended.  There is a small channel in the base to allow the wire from the connector to reach the center hole.  Carefully place the PCB into place, and the screen (if you didn’t already attach them, and then place your choice of the top piece over the the base.

Note:  the connector used for powering the LilyGo T-RGB is a Seeed Studio Grove connector.  This information wasn’t readily available, and the cable is not included with the display.  So be sure to order one.


Tagi