1 / 16
SKADIS Teeny Tote holder-v10 — zdjęcie 1
1 / 16

SKADIS Teeny Tote holder-v10

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

SKADIS Teeny Tote holder-v10

Ocena
0 / 5
Polubienia
37
Pobrania
49
Wydruki
0
Wyświetlenia
599
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Garage
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

SKADIS Teeny Tote holder-v10

This is my personal design for a SKADIS Teeny Tote wall mount / holder.

All parts have been printed out of 3d Fuel Tough Pro PLA+. (Lulzbot Green)

https://www.3dfuel.com/products/pro-pla-filament-lulzbot-green-1-75mm?variant=39755406770241

This is my own design to mount the SKADIS board and interconnect them vertically.

I will be adding a horizontal interconnect too.

I also uploaded the STEP file of my design. That way you can play with it so you can customize it.

Full panel holds 39 Teeny Totes.

I used a M3 Stainless Steel melt-in insert for the corner mounts.

https://www.mcmaster.com/94459A724/

If you have 2 or more vertical mounted SKADIS boards and want to interconnect them, then here is the mount.

Wall mount screws to hit your studs. This is what I used.

https://www.mcmaster.com/96832A240/

To mount the SKADIS board to the printed corner mounts, I used this M3x16mm torx screw. This is the same screw I use to mount the Teeny Tote holder with the printed t-nuts.

https://www.mcmaster.com/90910A573/

Now that the SKADIS wall mounting is covered, lets move on to the Teeny Totes...

I purchased these Teeny Totes from Lowe's.

https://www.lowes.com/pd/Project-Source-Teeny-Commander-X-small-Clear-Stackable-Tote-with-Standard-Snap-Lid/5018073195

https://www.lowes.com/pd/Project-Source-Project-Source-X-small-Clear-Stackable-Tote-with-Standard-Snap-Lid/5018732873

My newest design is on the bottom. Allows you to remove to Teeny Tote without lifting all the way up.

On my top holder you would have to lift the Teeny Tote all the way up to remove. It needed more clearance.

I could have designed a 3mm t-nut, but this one is good. I have to give credit to the creator. It is not my design.

Same Torx screw used previously to mount the SKADIS to the corner mounts.

M3x16mm torx screw

https://www.mcmaster.com/90910A573/

All my items were printed with 3d Fuel Tough Pro PLA+.

https://www.3dfuel.com/products/pro-pla-filament-lulzbot-green-1-75mm?variant=39755406770241

Special add-on is a Side-X-Side version. It will print on a PRUSA CORE One-L. I don't have one, so I can't print in this orientation. But here is a picture of the model. Someone please post a picture of this SXS. Model is in the list for downloads.

Here is the above Side-X-Side version that is split in half for printing on a PRUSA Core ONE.

Tagi