LayersFactory
Zgłoś model
1 / 7
DS18B20 "Plugable Terminal" Module Case (ESP32) — zdjęcie 1
1 / 7

DS18B20 "Plugable Terminal" Module Case (ESP32)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

poncho

poncho

@poncho87_1201744

Snap-fit enclosure for the DS18B20 "Plugable Terminal" breakout (ESP32). Self-supporting teardrop cable ports.

Ocena
0 / 5
Polubienia
0
Pobrania
13
Wydruki
0
Wyświetlenia
97
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Share Alike
SzczegółyPliki (2)Wydruki i komentarze (Wydruki: 0) (Komentarze: 0)Remiksy (0)Kolekcje (1)Powiązane

A compact two-part enclosure (base + lid) that protects the common **DS18B20 "Plugable Terminal" breakout board** — the one with the green screw terminal and the DAT / VCC / GND header (PCB marked V1738). I use it to wire a DS18B20 temperature sensor to an ESP32, but it fits any 3.3 V / 5 V MCU that talks to this board.

The box keeps the exposed PCB, screw terminal and jumper wires safe from dust, shorts and accidental knocks, while leaving the cabling accessible through the side openings.

Features

  • Snug fit around the standard DS18B20 plugable-terminal breakout.

  • Separate base + lid so you can service the wiring without desoldering anything.

  • Side cable pass-throughs for the sensor lead and the DAT/VCC/GND jumpers, shaped as teardrops so they print clean with no bridging and no supports.

  • The teardrop port is 4 mm — sized to grip the DS18B20 cable snugly with no play, acting as built-in strain relief so tugging the cable won't stress the PCB.

  • Chamfered edges — no sharp corners, cleaner print, easier to handle.

  • Small footprint, prints in minutes with almost no filament.

Dimensions

Part

Size (X × Y × Z)

Base

37 × 24 × 15.1 mm

Lid

37 × 24 × 2.5 mm

Assembled

37 × 24 × 17.5 mm

What you need (not included)

  • DS18B20 "Plugable Terminal" breakout board (screw-terminal version, DAT/VCC/GND).

  • DS18B20 temperature sensor (bare or waterproof probe).

  • Jumper wires + your MCU (ESP32, Arduino, etc.).

Files

  • Base – Body_DS18B20.stl

  • Lid – Lid_DS18B20.stl

Print settings

Printed and tested on a Creality Ender-3 V2 Neo in PLA:

Setting | Value

Layer height

0.2 mm

Infill

15–20 %

Walls

3 perimeters

Supports

Not required

Adhesion

None (brim optional)

Nozzle

220 °C

Bed

60 °C

Orientation

Base printed open-side up, lid flat

No supports needed if you print the base with the open side facing up.

Assembly

  1. Seat the breakout board inside the base.

  2. Route the sensor lead and the DAT/VCC/GND wires through the side openings.

  3. Press the lid on top.

Notes

  • Designed in FreeCAD. Source .FCStd can be shared on request if you want to remix or resize it.

  • If your board is a slightly different variant, scale on the X/Y axes to adjust the internal clearance.

Feedback & improvements welcome

Got an idea to make this better — a tighter fit, extra mounting options, a different cable routing? Leave a comment or post a "Make". Suggestions and remixes are very welcome, and I'll fold good ones into future versions.

Prints, remixes and photos welcome — enjoy! 🌡

Tagi

caseenclosuresensorarduinoelectronicstemperatureesp32thermometerds18b20breakoutesp32caseonewire