1 / 3
Caulk / Silicone Nozzle — Bendable up to 160°, Cuttable Tip (fully parametric) — zdjęcie 1
1 / 3

Caulk / Silicone Nozzle — Bendable up to 160°, Cuttable Tip (fully parametric)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A caulk nozzle that actually screws onto your cartridge. Cartridge threads are far less standard than they claim — so th

Ocena
0 / 5
Polubienia
0
Pobrania
26
Wydruki
0
Wyświetlenia
93
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Tools
Licencja
Creative Commons — Attribution — Noncommercial — NoDerivatives

Every caulk nozzle in the box is straight, too short, and the hole is in the wrong place. So I drew one you can bend, cut, and actually screw on.

## Why it fits cartridges that don't agree with each other

I measured three brands of 310 ml cartridge. The thread diameter was 15 mm on all three — but the pitch ranged from 2.07 to 2.50 mm. A rigid, deeply-threaded nozzle cannot possibly fit all of them, whatever the packaging says.

So this one doesn't try. It engages only 2 turns, the thread groove is deliberately loose in the axial direction, and a conical seat above the thread is what actually centres and seals against the cartridge spout. The thread's only job is to pull the nozzle on — the cone does the rest.

That's how factory nozzles work, and it's why they screw onto anything.

## Print settings — please read, the thread depends on it

Layer height 0.12–0.15 mm. This one is not optional.

The threaded socket is a helical overhang. At 0.20 mm layers, each layer oversteps its own extrusion width, the thread crests sag inward, and the nozzle won't screw onto the cartridge. I know because that's exactly how the first version of this model failed. At 0.15 mm it prints clean; at 0.12 mm it's perfect.

- Layer height: 0.12–0.15 mm ← the one that matters

- Orientation: threaded collar down on the plate, tip up

- Supports: none for the straight version. Only for bends over 60°, and only under the curve. Never inside the thread — your slicer may want to; don't let it.

- Material: PETG (best — cured silicone peels straight off), PP or ASA. Not PLA: too brittle at the collar and it doesn't like sealant solvents.

- 3 perimeters · 20–30% infill · cooling 100% · "slow down for overhangs" on

## What's here vs. what's on the site

The three STLs above cover the common cases. If you want your length (40–250 mm), your bend angle (0–160°), your tip hole (1–6 mm) or a different thread clearance, the model is fully parametric — set the sliders, see it in 3D, download free:

👉 https://marinelab3d.com/products/silicone-caulk-nozzle-extendable-bendable-310ml-10oz-parametric-3d-print

## Changelog

v2 — reworked the thread. The previous profile was, frankly, unprintable: the overhang was steeper than the extrusion could bridge, so the crests drooped and closed the bore. Now it's a buttress profile with a long, printable overhang ramp, a wider collar (real wall behind the thread), a conical sealing seat, and an adjustable thread clearance. Thanks to the first person who downloaded v1 — sorry about that one.

Tagi