FireBoard Pellet Drive Mount for Oklahoma Joe's Grills
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Pellet Drive mounting solution for Oklahoma Joe's pellet grills that use the rectangular controller housing.
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 2
- Wydruki
- 1
- Wyświetlenia
- 52
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Outdoor & Garden
- Licencja
- Open Community License v1.1 + General Attribution v1
The compatibility list on the FireBoard site makes it clear that the OKJ pellet smokers are not the best fit for the Pellet Drive even though many use the same standard main components as brands FireBoard does support. The main issue is physical fit since OKJ likes to make grills that are very round, and mostly use the same long rectangular face plate for their controllers. This project makes a suitable flat surface that hangs down from the stock controller housing on which to mount the Pellet Drive, and then fills the gap on the right side with a blanking plate that includes a phone holder.

In the future I may design a better system to customize that right side space for holding a bottle or other FireBoard products.
This project was made using 3D scans of both the OKJ housing and the pellet drive. This fit my grill pretty well as a result. I did try to leave some tolerance and room for adjustment to hopefully fit other people's units reasonably well.
Material Disclaimer:
This mounting plate is best printed using ASA and was designed with ASA shrinking in mind. ASA's properties are the best for this application since it will see UV exposure, humidity swings, heat from both the sun and smoker itself, and clamping forces from the fasteners.
Required Hardware:
M2.5 x 3.5 x 4 heat set inserts (3 or 6 if using the optional brace)
M5 x 15 screws (4)
M2.5 x 6 screws (3)
M2.5 x 10 screws (3, for using the optional center brace)
Washers for M2.5 screws (for direct use on slotted holes if NOT using the center brace)
* I used a multi pack for all the M2.5 screws and washers like this one.
Printing and Assembly:
I had reasonable luck using Overture ASA on the Prusa satin sheet with no glue stick. The smaller blanking plate for the right side gap printed fine for me, but I always had at least a little warping on one corner of the controller plate. This ended up not mattering much since any defects will face inward and any minor warping can be flattened out by the case screws/optional center brace.
I have included the project file with my filament settings for printing on a Mk4s in an enclosure.
Once the parts are printed, set the M5 inserts in the 4 blind holes on the front of the controller plate. If not using the center brace, only set M2.5 inserts in the 3 outer blind holes on the back side of the controller plate, otherwise set all 6 backside holes with M2.5 inserts.
Line the controller side up first and fasten to the metal housing using the stock panel screws in the 3 counter bored holes. Slide the right side plate behind the controller plate and align with the bolt holes. Loosely start the screws and then flip the housing over to line up the backside M2.5 screws. If not using the center brace, place a washer on each of the M2.5x6 screws and thread them through the slots to the outer inserts.
If using the center brace you will not need washers since the brace will provide enough support to keep the screws from sinking into the plastic. Using the brace will require using 3 M2.5X10 screws on the outer inserts and moving the 3 M2.5x6 screws to the inner line of inserts.
Once everything is loosely in place, press everything together from the left and right to make the center gap as small as possible and carefully start tightening everything starting with the stock housing screws.
With the panels in place, you can place the 4 M5 screws inside the Pellet Drive unit's holes and close the seal covers to retain them. Place the standoffs over each screw on the backside and slowly tilt the unit onto the plate. Open and partially thread each screw one at a time until all are started. Tip the unit so it is facing up while feeding the grounding wire through the smaller cut out. Make sure the Pellet Drive is properly aligned and the gasket is not unseated from the unit. Proceed to tighten the screws until you feel it press against the spacer.

Hold the housing up to a light to ensure the seal has pressed correctly onto the plate, and that there is no significant warping in the middle where the 2 plates meet. If the plates are bowing out and you did not use the brace, adding it is recommended.
You are now ready to follow the FireBoard wiring instructions. I left enough room that it should be not too hard to reach in to connect your pit probe and main wiring harness.