1 / 3
Azoteq TPS43 Trackpad Holder for Corne V4 Pro Micro Edition (right hal — zdjęcie 1
1 / 3

Azoteq TPS43 Trackpad Holder for Corne V4 Pro Micro Edition (right hal

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

# Azoteq TPS43 Trackpad Holder for Corne V4 Pro Micro Edition (right half) A drop-in trackpad mount for the **Corne V

Ocena
0 / 5
Polubienia
3
Pobrania
24
Wydruki
0
Wyświetlenia
106
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Accessories
Licencja
Creative Commons — Attribution

# Azoteq TPS43 Trackpad Holder for Corne V4 Pro Micro Edition (right half)

A drop-in trackpad mount for the Corne V4 Pro Micro Edition (Kea Workshop

PCB). It carries an Azoteq TPS43 capacitive trackpad (43 × 40 mm, IQS572)

and bolts onto the right half using the existing RP2040 cover screw holes —

no drilling, no PCB modification. Single printable part.

Project (firmware + sources + STLs):

https://github.com/jos3duardo/corne-tps43-oled

## Features

- Single piece: trackpad frame + factory mounting tab

- Reuses the original RP2040 cover screws — bolt-on, reversible

- Internal retention tabs hold the pad captive against the lid

- Separate 0.6 mm lid that doubles as the touch overlay

- Open bottom: routes discrete wires (SDA, SCL, 3V3, GND) — no FPC needed

- Flat base — prints without supports

## What you need

- 1 × Azoteq TPS43 trackpad module

- 4 × wires (SDA / SCL / 3V3 / GND)

- 2 × M2.5 screws (the original RP2040 cover screws)

## Print settings

- Material: PLA or PETG

- Layer height: 0.2 mm

- Perimeters: 3+ (the lid is thin — it's the touch surface)

- Supports: none · Lid printed flat side up

## Assembly

1. Peel the liner from the pad's factory adhesive (it's on the **sensing face** — intentional).

2. Stick the sensing face to the underside of the lid. The lid is the

overlay you touch, not the bare pad.

3. Drop the pad + lid into the frame; the retention tabs hold it.

4. Solder the four wires and route them through the open bottom.

5. Bolt the piece onto the right half with the original cover screws.

Firmware

Requires QMK/Vial built with the azoteq_iqs5xx driver (stock Kea Workshop

firmware does not include it). I2C on pads D1/D0 (GP2 = SDA, GP3 = SCL),

preset AZOTEQ_IQS5XX_TPS43, ROTATION_270. Full notes in the repo above.

Overlay note

Keep any surface over the sensing face between 0.2 and 1.2 mm and

non-conductive — no metal, metallic paint, or aluminium tape.

## Credits & license

Mounting tab derived from the Corne V4 Pro Micro Edition cover by **Kea

Workshop (klouderone)**, licensed CC BY 4.0 + MIT (© 2023 foostan for the

original Corne). Both permissive; commercial use and modification allowed with

attribution. Shared here under the same terms.

Tagi