1 / 4
NCS-15x2 - Noctua Cooler Shroud for Gigabyte 9070xt Gaming OC — zdjęcie 1
1 / 4

NCS-15x2 - Noctua Cooler Shroud for Gigabyte 9070xt Gaming OC

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A replacement fan shroud for the Gigabyte 9070xt Gaming OC GPU designed to hold 2x 15mm slimline NF-A12x15 Noctua fans

Ocena
0 / 5
Polubienia
6
Pobrania
13
Wydruki
0
Wyświetlenia
205
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
GNU General Public License v3.0

Bill of materials:

  • 4x M2x4mm Threaded heatset Inserts

  • 4x M2x5mm Thumbscrews

  • 3x M4 Self Tapping Fan screws (should be included with your fans)

  • 1x PH2.0 4PIN PWM fan adaptor cable

  • Zip-Ties to taste

  • 2x Frame.stl

  • 8x Gubbin.stl

Print Instructions:

Print with the "front" face on the build plate, so that the holes for mounting are facing up. For the Gubbins, make sure the tabs are facing up rather than sideways to avoid any overhangs.
I printed this on a Bambu A1 using the 0.2mm standard profile for PETG with a 0.4mm nozzle, but I recommend changing the following:

  • Infill density: 10%

  • Infill pattern: Gyroid

  • Supports: None

Installation:

  1. Remove the stock cooler from the GPU (you may need to cut the RGB cable as the plug is in the middle of the board under the heatsink and thus almost impossible to remove)
    This can be done without removing the heatsink from the GPU, it just requires a long, thin driver and some patience.

  2. Install the threaded inserts to the four mounting holes
    For the frame closest to the power cables, this is the two inner-most holes (left-hand side on the below image)
    For the opposing side closest to the outputs, you need to use the inner-most hole facing the PCIE Slot, and the outermost hole opposing it (top-right on the below image)

  3. Screw the two frame halves together using the M5 Self Tappers

  4. Carefully align 4 gubbins to the corners of each fan and insert the fan into the frame

  5. Screw the combined cooler to the GPU heatsink
    I found using a pair of needle-nosed pliers was the easiest way to get to some of these - you could also use Allen-key bolts and a wrench for the tight spacing

  6. Zip-tie cables to taste

Detailed Description:

This is intended to solve a very specific and niche problem I have, where almost every 9070xt card will not fit in a Jonsbo T9 (or many other similar) ITX PC case, at least not without sacrificing a good centimetre or two from your CPU cooler.  As there is pretty much ~16mm of clearance between the top of the radiator and the side panel, I needed something that would hold two 15mm fans without adding any thickness. This NCS-15x2 sits at exactly 16mm thick, holding the fans flush against the radiator and has a 1mm gap to prevent the mesh on the side panel from rubbing on the fan.

This mod does appear to improve the cooling performance however I have not done extensive testing as the primary goal of this was to fit the card into my case. if you do not have any issues with fitment and want even more cooling capacity, see the mod guide linked below.

It is designed to be mounted using M2x4mm threaded heatset inserts, with an M2x5mm thumbscrew from the back. The thumbscrew allows it to be tightened sufficiently without needing to fit a screwdriver behind the heatsink (as this is practically impossible without removing the heatsink from the card), though you may prefer bolts with an allen key (hex head) for a bit more torque and to make it easier to install/remove

I am using a PH2.0 -> 4pin PWM adaptor cable like this one to connect the fans to the GPU.  You may also wish to shorten the cables on the NF-a12x15 but a few zipties will get the job done just as well.

Before this, I had connected the fans to a header on the motherboard at set them at a fixed speed, however this is not an amazing solution as it is louder than needed at low load and hotter than comfortable at higher load.

STEP files are included for any modifications if needed or desired

I recommend using PETG or other similar high-temp resistant filament, in particular Elegoo Rapid PETG Brown and Elegoo Rapid PETG Beige are very close to the Noctua colours
Elegoo Rapid PETG filament Brown 1.75mm 1kg | Jaycar Australia
Elegoo Rapid PETG filament Beige 1.75mm 1kg | Jaycar Australia
While Noctua do make specifically tailored PLA, this will get soft and lose dimensional stability at temps around 60-100c which makes it a terrible fit for a GPU cooler.

Shoutout to Potatoes for his original guide that helped quite a lot in the design of this shroud.

Change history:

  • Added a variant for A12x25mm Fans (Untested as I do not have 25mm fans)

  • Added 0.5mm radius to inside edge to prevent sharp corners

  • Updated Render screenshots

  • Added printing instructions

Tagi