1 / 4
32 mm Hydraulic Hose Clamp / Ham Radio Antenna Element Mount — zdjęcie 1
1 / 4

32 mm Hydraulic Hose Clamp / Ham Radio Antenna Element Mount

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Two-piece clamp designed for 32 mm hydraulic hoses, pipes and aluminium tubes. It can also be used as a strong mounting

Ocena
0 / 5
Polubienia
11
Pobrania
45
Wydruki
0
Wyświetlenia
220
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Tools
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

32 mm Hydraulic Hose Clamp / Ham Radio Antenna Element Mount

A two-piece clamp designed for holding a 32 mm diameter hydraulic hose, pipe, tube, or amateur radio antenna element.

The split design allows the clamp to be installed around an existing tube or hose without sliding it over the end. It can be used for hydraulic hose organization, mechanical DIY projects, or amateur radio antenna construction.

For antenna projects, the clamp can be used for mounting aluminium elements, support tubes, boom components, coaxial cable supports, or other cylindrical parts with an outside diameter of approximately 32 mm.

Features

  • Designed for 32 mm outside-diameter tubes, hoses, and antenna elements

  • Two-piece construction for easy installation

  • Can be installed without removing or disconnecting the tube

  • M6 mounting and clamping holes

  • Upper part includes recessed holes for M6 socket-head cap screws

  • Lower part includes M6 through-holes

  • Flat lower mounting surface for attachment to a metal plate, antenna bracket, or other support

  • Suitable for Yagi, dipole, vertical, and other amateur radio antenna projects

  • Suitable for hydraulic hose organization and non-pressure-bearing support

  • Designed to print without complicated support structures

  • Suitable for outdoor printing materials such as ASA or PCTG

Dimensions

  • Internal diameter: 32 mm

  • Overall assembled height: 52 mm

  • Overall assembled width: 75 mm

  • Overall assembled depth: 29.8 mm

  • Fastener size: M6

Overall assembled dimensions:

H 52 × W 75 × D 29.8 mm

Recommended Materials

ASA — Recommended for Outdoor Use

ASA is the recommended material for permanent outdoor antenna installations because of its resistance to:

  • UV radiation

  • Rain and moisture

  • Temperature changes

  • Long-term outdoor exposure

PCTG — Recommended Alternative

PCTG is also a suitable choice because of its:

  • Good mechanical strength

  • High impact resistance

  • Strong layer adhesion

  • Lower brittleness compared with standard PETG

PETG may be used for prototypes, indoor use, or lighter-duty applications. ABS, PA, or other durable engineering materials may also be suitable when printed correctly.

For permanent outdoor antenna installations, ASA is the preferred material, with PCTG as a good alternative.

Recommended Printing Settings

  • Layer height: 0.20 mm

  • Walls/perimeters: 5 or more

  • Top layers: 5 or more

  • Bottom layers: 5 or more

  • Infill: 40–60%

  • Recommended material: ASA or PCTG

  • General-purpose material: PETG

  • Supports: Depending on print orientation and printer settings

Print both parts with their largest flat surface placed on the build plate.

For mechanically demanding installations, additional walls are generally more useful than extremely high infill.

Required Hardware

The clamp is designed for use with:

  • M6 socket-head cap screws

  • M6 washers

  • M6 nuts or threaded mounting hardware

  • Optional metal mounting plate or antenna bracket

The upper part contains recessed holes for the M6 socket-head screw heads.

The M6 screws pass through the lower part, allowing the clamp to be attached to a metal plate, antenna support, boom bracket, or another mounting surface.

Hardware is not included with the model.

Assembly

  1. Place the upper and lower clamp halves around the 32 mm tube, hose, or antenna element.

  2. Insert the M6 socket-head screws through the recessed holes in the upper part.

  3. Pass the screws through the lower clamp part.

  4. Attach the clamp to the required mounting plate or support.

  5. Install washers and nuts where required.

  6. Tighten both sides gradually and evenly.

Do not overtighten the screws, especially when clamping:

  • Soft hydraulic hoses

  • Thin-wall aluminium tubing

  • Plastic pipes

  • Easily deformable antenna elements

Excessive tightening may deform the tube, damage the hose, or crack the printed clamp.

Important Safety Notice

This printed part is intended only for supporting, positioning, organizing, or mounting a hydraulic hose.

It is not:

  • A hydraulic fitting

  • A pressure connector

  • A hose repair component

  • A load-certified structural clamp

  • A safety-critical hydraulic component

Do not use the printed clamp as part of a pressurized hydraulic connection or as a replacement for certified hydraulic hardware.

For antenna installations, the required material, wall thickness, infill, fasteners, mounting plate, and installation method depend on:

  • Antenna size

  • Element length

  • Wind load

  • Installation height

  • Temperature

  • UV exposure

  • Mechanical vibration

Inspect and test the printed parts before permanent installation. Periodically check outdoor parts for cracks, deformation, loose fasteners, and UV or weather damage.

Suggested Applications

  • 32 mm hydraulic hose support

  • Hydraulic hose organizer

  • 32 mm pipe clamp

  • Aluminium antenna element clamp

  • Yagi antenna element mount

  • Dipole antenna support

  • Vertical antenna support

  • Coaxial cable support

  • Antenna boom component

  • Tube and pipe mounting

  • Workshop organization

  • Custom mechanical projects

  • Amateur radio DIY projects

Tagi