Zuru XSHOT Break Barrel Upgraded Iron Sights
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Fast acquisition, high contrast dot sights which speed up aiming and work better in low light environments.
- Ocena
- 5 / 5
- Polubienia
- 11
- Pobrania
- 48
- Wydruki
- 1
- Wyświetlenia
- 284
- Oceny
- 2
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Toys & Games
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Update 29/08/2026:
By request, I have added an additional version of the rear sight which features openings in the top of the sight block to allow for light gathering (when used with translucent filament pieces) much like the front sight. I have not printed/tested this part yet, so I am unable to verify printability, but it looks fine in the slicer preview. Feedback welcome :)
Introduction:
Upgraded, drop-in/on replacement iron sights for the Break Barrel. These sights provide a clean, easy to read sight picture with contrasting dot inserts (1.75mm filament cut to size) resulting in quicker acquisition, easier both eyes open shooting and better legibility in low light environments. Easily reversible/removable, no permanent modification to the blaster is required.
Printing Recommendations:
0.15mm Layer Height, 100% Infill in PETG (in a dark colour to contrast with the dots).
Print in the orientation shown in the file.
Small supports are recommended for the rail stops on the front sight.
To achieve the textured pattern on the sight faces, I used the textured steel sheet on my Core ONE.
Post-processing:
The only extra processing required is preparing your choice of filament for the contrasting dots. In my example, I used Prusament Orange PETG. You could get really fancy with translucent filament for the front sight (which features an opening for light gathering) or even glow in the dark filament!
1.) Use a sharp craft knife to cut suitable lengths of filament. Do your best to make the cuts at right angles in order to keep the end faces flat and perpendicular. You should aim to cut the filament pieces just long enough to leave them slightly proud when installed, this will be explained in the next step. You'll need two pieces for the rear sight and one for the front. If you wish to measure your cuts instead of eyeballing them, the hole depths are:
Rear: 17.5mm
Front: 16.5mm
2.) Using a fine grit sanding sponge, clean up the newly exposed faces. Use a circular motion and intentionally round over the edges slightly to achieve a convex appearance. The result; the dot appears '3D' when installed in the sight, making it more visible by bouncing light from more angles, and also diffusing said light to reduce glare/harsh reflections.
Note: it is possible to remove the front filament piece with relative ease owing to the opening in the sight notch, but once the pieces are inserted and fully seated into the rear sight block, they cannot be removed.
End Result:
The end result should look something like this:


Installation:
For the front sight; align it with the front end of the rail, tall end (dot side) oriented toward the rear. Lever it on from the side. It cannot be slid on from the front as the integrated rail stops which keep the sight in place prevent this. PETG is plenty flexible to allow for this procedure without deforming or breaking. I have not tested printing these parts in PLA but it may be too brittle to be fitted this way.
For the rear sight; only slight disassembly is required—that is, if you consider 'disassembly' taking out two screws. Remove the two top, rearmost screws near the factory rear sight. Next, pry apart the blaster shell enough to insert the new sight between the old one. You may find using a plastic pry tool makes this part easier. Finally, close the shell back up. Take care not to overtighten or cross thread the screws when reinserting. For best results, offer up the screw to the hole and back it out (counter-clockwise) until you feel/hear the thread 'drop' into the track. This means the screw is meshing properly with the already cut thread in the plastic. Tighten until slight resistance is encountered.
Makes/Comments:
I'd love to see your results or hear your comments, so if you happen to make these sights, please share!
Other Models:
I also made a version of these sights for the Motorized Thrasher, check them out here: