ASUS TUF 3080Ti 120mm Fan Shroud
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A fan shroud that reversibly converts the loud, three fan cooler of the stock ASUS TUF 3080Ti into a 2x 120mm design.
- Ocena
- 5 / 5
- Polubienia
- 2
- Pobrania
- 17
- Wydruki
- 1
- Wyświetlenia
- 186
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Computers
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Summary
I was not happy with the stock fans of my ASUS TUF 3080Ti. They are incredibly loud. I wanted to convert the cooler to use quieter 120mm fans. I also did not want to damage my GPU at all, so I designed this two part GPU shroud to fit around the stock heat sink brackets, so this is fully reversible.
Do not use this design if you're looking to maximize cooling performance. For that, you typically try and get the fan as close as possible to the heat sink to maximize the static pressure performance of the fan. For this GPU, that will require irreversible bending / cutting of stock cooler tabs.
Materials
You will need
PETG filament (better heat resistance than PLA)
Wall thickness is optimized for a 0.6mm nozzle
I printed it at 50% infill, but stock 15% is probably fine
I printed it with support only on the build plate
8x M3 heat set inserts
8x 30mm countersunk M3 bolts
an ASUS 7pin fan connector to 2x 4pin fan adapter
Installation
You do not need to remove the cooler from the card, only the metal shroud.
Unplug the two connectors at the back of the card underneath the heat sink
This is a bit fiddly to release the catch on the connectors - needle noise pliers can help
The 7pin connector is for the fans, and the smaller connector is for a little LED on the shroud
Unscrew the 6 small countersunk screws around the edges of the metal GPU shroud
Keep the screws - we will reuse them for the new 3D printed shroud
Unscrew the stock fans from the cooler and all wiring brackets for the fans
You will need to rotate the fans by hand to access the screws, fitting a small screwdriver between the blades
I put the fan screws back into the cooler after removing the fans - easy way to keep track of the screws
Install the heat set inserts into the plastic
If you don't have a soldering iron, you can thread the insert onto the bottom of a long M3 bolt and hold it over a flame with some pliers (e.g. a stove, a lighter, etc.) to get it hot enough for inserting into the plastic
Install part "A" on the cooler (the side closest to the rear IO) with two of the small counter sunk screws from the original GPU shroud
Install part "B" on the remaining half of the cooler with the remaining four small counter sunk screws from the original GPU shroud.
Install the ASUS 7pin to 2x 4pin fan connector adapter cable
Install your 2x 120mm fans
I've designed the shroud specifically for the [NF-A12x25 G2 PWM Sx2-PP](https://www.noctua.at/en/products/nf-a12x25-g2-pwm-sx2-pp-chromax-black) kit where the fan is mounted to push air into the cooler
This mod adds about 25mm of height the card and a fair amount of weight (2x 25mm x 120mm fans are pretty heavy), so having a GPU brace of some kind is a good idea.
Results
I don't have true apples to apples comparison of just the effect of the fan change on cooling because I also replaced the thermal paste and thermal pads while doing this, but fan noise is significantly better. I can have the fans at 100% (~1800 RPM for the NF-A12x25 G2 compared to 2.5k+ for the stock fans), and it is a very subtle noise compared to the stock jet turbine sound.
Keeping in mind that I swapped thermal paste (probably didn't need to do the pads, they felt fine), GPU temps are ~10C lower and hot spot temp is 20C lower.