1 / 5
ASUS TUF 3080Ti 120mm Fan Shroud — image 1
1 / 5

ASUS TUF 3080Ti 120mm Fan Shroud

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

A fan shroud that reversibly converts the loud, three fan cooler of the stock ASUS TUF 3080Ti into a 2x 120mm design.

Rating
5 / 5
Likes
2
Downloads
17
Makes
1
Views
186
Reviews
1

Updated at source:

Model information

Category
Computers
License
Creative Commons — Attribution — Noncommercial — Share Alike

Summary

I was not happy with the stock fans of my ASUS TUF 3080Ti. They are incredibly loud. I wanted to convert the cooler to use quieter 120mm fans. I also did not want to damage my GPU at all, so I designed this two part GPU shroud to fit around the stock heat sink brackets, so this is fully reversible.

Do not use this design if you're looking to maximize cooling performance. For that, you typically try and get the fan as close as possible to the heat sink to maximize the static pressure performance of the fan. For this GPU, that will require irreversible bending / cutting of stock cooler tabs.

Materials

You will need

  • PETG filament (better heat resistance than PLA)

    • Wall thickness is optimized for a 0.6mm nozzle

    • I printed it at 50% infill, but stock 15% is probably fine

    • I printed it with support only on the build plate

  • 8x M3 heat set inserts

  • 8x 30mm countersunk M3 bolts

  • an ASUS 7pin fan connector to 2x 4pin fan adapter

Installation

You do not need to remove the cooler from the card, only the metal shroud.

  • Unplug the two connectors at the back of the card underneath the heat sink

    • This is a bit fiddly to release the catch on the connectors - needle noise pliers can help

    • The 7pin connector is for the fans, and the smaller connector is for a little LED on the shroud

  • Unscrew the 6 small countersunk screws around the edges of the metal GPU shroud

    • Keep the screws - we will reuse them for the new 3D printed shroud

  • Unscrew the stock fans from the cooler and all wiring brackets for the fans

    • You will need to rotate the fans by hand to access the screws, fitting a small screwdriver between the blades

  • I put the fan screws back into the cooler after removing the fans - easy way to keep track of the screws

  • Install the heat set inserts into the plastic

    • If you don't have a soldering iron, you can thread the insert onto the bottom of a long M3 bolt and hold it over a flame with some pliers (e.g. a stove, a lighter, etc.) to get it hot enough for inserting into the plastic

  • Install part "A" on the cooler (the side closest to the rear IO) with two of the small counter sunk screws from the original GPU shroud

  • Install part "B" on the remaining half of the cooler with the remaining four small counter sunk screws from the original GPU shroud.

  • Install the ASUS 7pin to 2x 4pin fan connector adapter cable

  • Install your 2x 120mm fans

  • This mod adds about 25mm of height the card and a fair amount of weight (2x 25mm x 120mm fans are pretty heavy), so having a GPU brace of some kind is a good idea.

Results

I don't have true apples to apples comparison of just the effect of the fan change on cooling because I also replaced the thermal paste and thermal pads while doing this, but fan noise is significantly better. I can have the fans at 100% (~1800 RPM for the NF-A12x25 G2 compared to 2.5k+ for the stock fans), and it is a very subtle noise compared to the stock jet turbine sound.

Keeping in mind that I swapped thermal paste (probably didn't need to do the pads, they felt fine), GPU temps are ~10C lower and hot spot temp is 20C lower.

Tags