1 / 18
XENO - Full Length Bullpup Coaxial Nerf Blaster — zdjęcie 1
1 / 18

XENO - Full Length Bullpup Coaxial Nerf Blaster

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Taurus 2.0 and longshotaint

Ocena
5 / 5
Polubienia
25
Pobrania
31
Wydruki
1
Wyświetlenia
489
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Outdoor Toys
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

A collaborative attempt to find and remix the prototype XENOS into a functional blaster. 

notes for building- 

The SHIDDLE MID requires 8 4-40 standoffs. Putting in these standoffs is kinda tricky, I would use a finger in the middle to make a "shelf" to push the standoffs in the front holes. The back ones are relatively straight forward, but the holes need to be clean. 

Make sure the dart/barrel hole in the TA part is clean enough for darts to pass through without anything catching on it. It will cut darts if this hole is not clean. 

The thumbhole has a screw near the grip point. This screw is used to tension the pin on the grip from falling out. Do not tighten this screw too much or it will crack. 

The TRIG BOOBY has a screw post for the extension spring. Don't tighten too far down or this part will not move freely and jam the trigger. 

The RAM ALIGHNER BUT LONGER has an optional spot for the second screw point on the u channel, but I did not model a hole in for it.  You could use one of the coarse #4 screws to drive a screw straight in. Both this screw and the other one next to it needs to be flush or the pusher will catch on these screws.

You may need to shave off some material on the lower u channel if it block your magwell from inserting mags. 

The  MUZZZLE WID A SCREW IN IT may need supports, but is printer dependent.

The SPRING ALIGHNER needs a brim

The CHEEK REST BUT IT SWING OPEN is recommended to be printed on a smooth sheet, but is not required. 

The XCOLLET is technically not required, but does add some color to that area. I would not use its o ring holding feature as it doesn't hold the barrel and will get lubby.  

The PLUNGER GUIDE BUT MORE CHAMFERED may need supports. 

The side and top sears need to be printed with a lot of walls. 

There are folders named  BLAK and FLOORSCENT WHIT for a color reference. 

From my limited testing during prototyping, I think this blaster is dry fire safe to an extent, as the friction from the barrel to plunger is enough to not slam into the TA part hard. 

I found some vertical grips to not work well for priming this blaster, as the height to bore axis is large. The pryangle grip for some reason doesn't feel as bad as other vertical grips. 

There are several pictures of my blaster to show some "difficult" areas to help assemble your blaster.

There are also pictures of the parts orientations for printing. 

There is a bom for somewhat exact amounts of stuff (though I did not count the normal slugs parts well)  The important parts and descriptors required are below as well. 

Hardware that is not normal CS stuff or requires measurements- 

13 inch 10-32 threaded rod

2 10-32 acorn nuts. Optional for the rail top to cover the threaded rod. 

1 TCU U channel. Some holes need to be drilled wider to accommodate 3/16" pins

1 TCU U channel with no stock. 2 holes need to be drilled to fit  3/16" pins. Also needs additional drill holes for the second grip point. The easiest way to do it is to mount the grip and use a center punch to mark the drill spots in the back. The screws there do not need to be countersunk there as there is sufficient space for regular screws. 

2 inch OD 1.875 ID Plunger Tube. 7 inches   

2 or 3 V3 caliburn flatbars. One for the top transfer bar. 1 or 2 for the mag release. 

1 V3 talon claw flatbar 

2 of these 90485A160 but cut down for the grip front point. There is a picture on how much to cut. The point of cutting is to not have the screw hit the trigger bar so the length is not super important. 

#4 3/8 length 82 degree head 90485A160. I would use these for the grip points and some other screw mounts. You cannot use these in some spots and the standoffs. Use regular 4-40s for those. 

5 CS nylon spacer (94639A205) 4 are for the sears, one is for the transfer linkage. 

1 70A Buna-N U-Cup Seal 9691K54

Short, medium and long clevis pins. (1, 1.5, 2) You need all 3 in various places.  97245A119  98330A115 97245A129

Cotter pins for those pins 

131 O rings. X rings would be preferable for some spots, but are expensive. 

5/8 barrel. It must be 5/8 sized, it will add too much friction with anything larger. Expect to damage the barrel as this ONLY uses screw for barrel securing. (o rings and friction failed in testing) Barrel In the first photo is 22 inches. 

11 inch springs. The ends must be closed or it will not work. Confirmed springs are K25, 788 (super low powered though), k26, k14. K31 does fit, but I dont think it will fire, if at all, considering 788 barely works. 

17 4-40 Hex Standoffs. I would get more if you mess up the threads. 

1/8 and 3/32 elastic cord. The 1/8 is used for the mag release "spring" and the 3/32 is for the catch 

2 10-32 Screw .75 inches. One for the pusher bar aligner, one for the trig bob trigger connect. 

2 10-32 Screw 5/16 inch. For the barrel retention

2 10-32 Screw 1/4 inch. For the mag release bar nubs. These could be replaced with longer ones with a remixed nub block. 

2 -012 O ring. Both for the pusher. 

1 caliburn extension spring

-Improvments that could be made, but I dont wanna work on dis anymore

The sears could have more catch surface material. (being longer so it's not just a triangle tip on the end). This would require making them longer and modifying the plunger for that space.

The plunger could be made to use a 016 o ring instead of a u cup seal. This would require a redesign of the plunger entirely with 2 parts that screws on together, skewer style.

An actual spring for the mag release, not elastic. Extension spring seem fitting for that. 

-LE COLLABORATION CREDITS SECTION

_windX for acquiring the files and helping with making the blaster

Limelight and taffy for feedback

Silverfoxindustries for acquiring the files from slug 

Captain slug for making the base Xeno files

Tagi