Liczymy pasujące modele…
V2, and a much needed upgrade of the original barrel collet system I made for the Xshot Longshot, using the same internal barrel collet as the Unicorn Wings Kit that can be found here: LINK . This still has the version of the collet that…
To use, print both the left and right halves of either the “Low Profile” or the “Flared" versions. Both of these use the internals from the included X-Shot half length adapter, and both will require some cutting of the adapters…
Both parts are designed to be printed with no supports, Use a 4-40 x 3/8in screw in the front if the picc lock isn't staying in place. You will need to prime the blaster before installing. Don't have a printer? Order from OOD! Affiliate…
The grip is printed in two parts and clamps around the rail on the Longshot like the original grip. Printed without supports. Hardware: 3x M3x8 socket head screws
This is a scar for the Xshot Longshot blaster. The stock scar was non functional. 6/20/23 Working on updated version ** added new V2 improved rifling and less FPS drop ** 6/27/23 Adding Version for 16mm replacement barrels *** added V3…
Utilizing the groundwork laid by RedCowl and is V2 Barrel Collet front end and the o-ring collet system that SillyButts designed, I created this: a stylized front end for the X-Shot Longshot (or Lonxshot, Longxshot, etc.) that allows the…
I created this since there were not a lot, if any, cheek rests for LEFTYs... so i made my own!! My Stock Lock & Cheek Rest is a 2-Piece design. This allows for two things, (i) you can just use the Stock Lock by itself if you don't need…
This design is meant to be a press fit into the trapezoidal cutouts in the rails of the Xshot Longshot. This uses 2x toy screws (the normal screws that Nerf, Dartzone, and Xshot use to keep their blasters together). There are a ton of…
Cheek rest for your Longshot, as the stock cheek weld is terrible. Acts as a stock block too. Print both pieces, open Longshot stock to furthest position, put pieces in, secure with three toy screws- standard Nerf style. Mirror for lefties.
Simple 3D printable tube to replace a cracked plunger tube on an X-Shot Longshot. I recommend printing this with Orca slicer and scarf seams enabled to get the best inside surface finish. Attached .stl file and a .3mf file for use in Orca…
Update --------- BCAR Shroud 1.1 ------> X-Shot MPP (or LONGSHOT 2.0 with EXTENDED custom barrels) + optional Barrel Color Sleeve for the MPP Wrap two to three layers of e-tape around the narrower rear section of the BCAR and insert it…
Spring spacer for the XLS. Adds ~10mm of precompression 7.5mm, 12.5mm and 15mm sizes also available. Slight edge on the outer end to help the spring stay aligned. Highly recommend you print this in 100% infill for durability reasons. Not…
For those who want to print RedCowls fantastic xshot-longshot-half-dart-magwells but don't want to sacrifice the original magwell internals. Simply print the slide and two of the locks, put in a spring (I took a spring of a broken pen and…
A riser matching the profile of the Longshot. Brining the picatinny rail to the right height for an optic
My Boom grip, now remixed for the X-Shot Longshot. New this iteration: knurling. Neat. Uses one M5 bolt (either 30 or 35mm I think) and one M5 nut. Designed to be printed with the front end up - it'll bridge over the picatinny's end, no…
remixed for better retention with a 016 o-ring
A LEGO accessory based on the Nerf Longshot. Updated version with some tweaks to make the two halves look more like one complete blaster. This started as a post on r/nerf asking which blaster I should model next. I got dozens of…
Press fit PCAR for Xshot Longshot, using Thanhtacles 's trivicus 1.0. It fits the lines of the blaster well.
Want to add a longer barrel to your X-Shot Longshot ? Want the barrel held in place securely with a nylon thumbscrew such as used in the Lynx or SLAB? This is what you need! We have included a version for M3 and M4 thumbscrews/nuts so you…
A very low profile magazine release for use with the short-dart adapter. I don't recommend it for regular use with normal magazines as it is too difficult to operate quickly The spring post can be reinforced with a small screw if needed.
Update April 2024 - I suggest printing the carry handle in two parts, dovetailing it at the picatinny rail. This allows you to print it side down, costing less support material and also getting a more optimal print orientation for…
As it was too expansive and not able to deliver to france, I create my own billards longshot bridge. Of course if you are living in the country where it is sold, please buy the real version. This is a little bit customizable, meaning the…
This is a Longer version of @BrooklynTony198's X-Shot Longshot Barrel. It gives your Longshot more of a sci-fi look and I personally love it! In the pictures the barrel has a slight crack which I've fixed in the file so hopefully your…
Added a chamfer that was missing because it bothered me, that's it
UPDATED FILES Did you let a coworker try out your Longshot, and did he subsequently break the pusher while somehow full sending a double feed so bad it required a full disassembly of your blaster? Cause I did, and thats why I designed…
A grip designed for the XLS. Comes in a long and short version. The long version will come up to the trigger guard on prime and the short one will come up about an inch before the guard. When you print it use supports for the hand stop in…
Wanted to slow down the FPS for use in a low-speed game. Tested different lengths to see how it affected speed. With Adventure Force and Dart Zone short darts, the 60mm and 100 mm resulted in about a 10 FPS drop. The other length of SCAR…
PLEASE USE THE V2 - IT IS SO MUCH BETTER: Can be found here: LINK This is a drop in replacement for the front end of the X-Shot Longshot's front end. There are many parts included, as there are many ways to use this mod. First, you will…
MAGWELLS FOUND HERE: https://www.printables.com/model/512021-xshot-longshot-half-dart-magwells I apparently LARPed too hard when reloading my Lonxshot with RedCowl's more flush magwell installed, and managed to shear off both hard-stops…
Reinforced this nice frontend for the X-Shot Longshot because mine unfortately broke at the thread. It could be because of the crappy filament I used or all the silicone grease that has accumulated there at the front^^ I reinforced it in…
Simple yet highly effective! This reinforcement prevents your X-Shot Longshot Pusher from breaking. Did your pusher already snap? Print, push, glue, and you're back in action. If it's still intact, print and install this reinforcement for…
X-Shot Longshot – Aluminum Bar Dart Pusher This is a reinforced dart pusher designed specifically for the X-Shot Longshot. Unlike the stock plastic pusher, this design uses a solid aluminum bar joined with 3D printed end pieces to…
Improved model, for easier printability, supports are recommended. The short one is the top pin and the long one is the bottom one.
This allows you to shoot silly shells using your longshot. MAKE SURE YOUR LONGSHOT HAS A STRONG SPRING. The stock spring will work, but not very good at all. You will also have to download the lever and the piece that you screw the silly…
11" long Picatinny rail lifted 1" from the stock XLS rail. Designed as 5 separate pieces, with the supports each being a separate piece, the rail split into two pieces for ease of print, and a printed pin to index the front with the XLS…
This is a one piece magazine Talon magazine adapter for the X-Shot Longshot. It is intended to be a permanent install. The magazine retention is achieved with a pair of 6x7mm ball detents. This is loosely modeled after the piece that is…
When I replaced my x-shot longshot plunger tube the turnaround was brittle and cracked, this will replace that turnaround, use the original barrel o-ring. It need a little bit of support when printing. I printed it at 0.2mm, 2 walls, 15%…
This is a magwell adapter designed for the X-Shot Longshot, allowing it to accept Worker Talon short dart magazines . Key Features Compatible with the original short dart mag release lever. Includes an integrated, printed mag release…
This remix includes 3 main changes: The knob is now a knurled round knob that takes an M3x25 socket head screw, and should be printed at 0.1mm layer heights or lower in order to resolve the knurls. The knob includes sacrificial bridging…
This is my take on Sternendrache2's design. I did not modify his model, and instead designed my own from the ground up to more closely match the manufacturers original parts geometry. Due to this model performing the exact same function…
Pins for stock sights so you don't lose them. Friction fit them into the hole in the front of each sight. Printing tips: Max cooling, 100% infill, print multiple at a time with some distance to maximize cooling if your prints aren't…
Heatset inserts (M3 thread, 4mm length, 4.5mm outer diameter, 3.9mm nub)https://www.aliexpress.us/item/3256805034317562.html M3x10mm button head screw See original model for printing instructions. You probably want extra walls so there's…
I custom-built these lower-profile, larger side rails , inspired by RedCowl's Side Picatinny design. My goal was to mount accessories on the side rails without interfering with attachments on the main rail. You can customize your rail…
I printed the slide with the two “legs” that straddle the plunger tube on the build plate, this uses a bunch of support material, but should be the strongest. The knob should be printed on its side, requiring support on the part that goes…
After improving the internals of my XSLS, I took a look at my old carry handle and wanted to make some improvements. Lowered the carry handle significantly so you can now use a sight. Still, lower profile the sight, the better. More…
This is a barrel shroud and muzzle brake for a Nerf blaster, specifically the Longshot main gun. The shroud is designed to fit around a 318mm long, 16mm OD barrel (worker longshot kit) and inside the front locking lug of the blaster. The…
RIPPCAR with bigger OD to fit into the Xshot longshot
Level up your X-Shot Longshot with this all-in-one front end designed for both performance and aesthetics. Tired of simple, flimsy, or ill-fitting designs? This isn't a remix—it's a complete redesign built from the ground up, blending the…
A pretty basic part that blanks out the trigger safety on the X-Shot Pro Longshot. Installation requires some type of adhesive (I used hot glue) to retain these in place. Other than that, this should be a pretty simple install.
I got the degenerate version of the Longshot recently and have been meaning to turn it into a FAMAS ever since. There's some perfectly fine, well designed handles out there already but I wanted the practice and it ended up only taking an…
To install, unscrew the two screws that are in the pins - Remove the pins - Then pull the stock front end out. Then put the new one in, then put the pins in. Print it flat, like the others. No supports needed
Should be a straightforward print, lay the largest flat side down on your print bed, I set mine for 5 walls, 5 top and 5 bottom layers, which is pretty overkill. The hole on the top peg is sized to be tapped to M3, I used a screw and…
This is a modified cheek rest that allows for the jam door to be opened. This design only includes a modified right side cheek rest due to the jam door not being covered on the left cheek rest.
Made to work perfectly with a stock XShot Longshot. I extended the mounting area to 19 mm to get rid of the empty space that can hinder performance. I also added a screw hole on the side of the mount and expanded it to be able to screw it…
Drop in replacement for the Xshot longshot turnaround with a threaded barrel insert to suit worker style barrels. M16 x 1.0 ↓12mm Print upright with the mag end of the turnaround on the print bed. Supports required. O-ring may be tight…
This is a quick remix I threw together to allow me and my girlfriend to change barrels interchangeably between our Fury-X and and Longshots, I find the O-Ring system alot nicer to use than a fixed collet as it is alot more convenient. My…
The stock half-dart magazine release lever on my XShot Pro Longshot seemed a bit small for my thumb, so I made a customizable version of the arm that uses M3 screws for fastening (without the need for heat inserts). It should fit into the…
Replacement part for a old Nerf blaster toy. The original bolt handle came off due to the insides breaking (should look like this but the part that contacts the metal was broken off entirely). I wanted to replace the just broken part. I…
Here is some parts for your longshot. They are meant for if your gun breaks you can fix it. No need to thank. (:
Hello everyone! This is a toy scope that I designed to closely resemble the Nerf Longshot scope. I love the look of the Longshot scope, and I thought it would be fun to be able to print one in whatever colors I wanted. Additionally, once…
This replacement pusher design aims to mitigate several jamming scenarios with the stock pusher on the XLS which may be caused by stacking tolerances, including: Darts getting stuck in the pusher ring Darts getting pulled backwards on…
these are simple sights that dont need any hardware but you can use 3mm screws if you want. everything is a very tight fit but its soposed to be. the front sight post should be pushed all the way in and the rear sight post should match…
Hey guys after some requests I reuploaded the hookshot and Longshot to use a lot less material, also includes an alternate style hook for those who want a closer to classic look. (I plan to release a full line up of classic and remaster…
This is a X-shot Longshot mod that will max out the spring compression.
X-Shot Longshot Blaster silly shell adapter Directions For optimal results, consider printing with a variety of materials, although I highly recommend using PETG for its excellent durability and temperature resistance. Aim for a 35%…
The hole is 3.7mm wide by 4.6mm deep. Make sure your inserts are about 1mm wider than the hole (so there's plastic to grip) and not as deep.
BCAR Shroud -- X-Shot Longshot 2.0 (compatible with stock barrel, muzzle and BCAR) .... for a bit more color customisation on the blaster and to partially cover these unsightly high-gloss plastic parts. Shrouds for the X-Shot BCAR, to be…
The same design as the original except this time there is a QD mount on the right side of the blaster's stock. Works super well if you run the sling of the front of the top rail, over the left shoulder and then under the right arm and…
I very much liked RedCowls model, however there was not enough room at the end of my barrel to attach any muzzle devices. So I took the corrected champfer version of the model into blender and noticed internal geometry and other excess…
This is the Epic weapon, KBR Longshot, from the game The Cycle: Frontier. The Cycle: Frontier is a PvPvE first person shooter made by Yager Development. They had unfortunately announced that they will be shutting down the game as of…
Scanned Zuru Longshot Pro as a test piece. Scaled correctly. More models will come as I've scanned the inside and made upgrade parts.
The goal of this piece was to convert the stock longshot breech into a conventional pusher style breech with minimal modding effort. This is a work in progress, I'm currently in the process of adding additional orings and tweaking the…
Xshot Longshot Chunky Collet Much stronger than the original.
Print in place no supports 50% infill to make it strong at 0.2mm layers.
A barrel adapter for the X-shot Longshot SCAR that allows you to attach other barrels to it. This attachment will work with the X-shot longshot barrel as well as most Dart Zone barrel attachments. It will not work with attachments that…
Replacement plunger head for the longshot, to be used with 3.5mm o rings (I used 28mm ID). Ended up going with a o-ring seat that went from 28.4mm-29mm, found it gave a pretty good seal. I made this to experiment with seal strength, I'm…
Disassembly tray for the Nerf Longshot main gun. The shape of the tray somewhat resembles the gun outlines, the posts are roughly in the same spots as the screwholes. Smaller trays in the main body area for some (maybe even all) of the…
A remix of the turnaround to allow room for the magazine.
Got a second-hand xplorer pump grip and I noticed that the bolt head and nut were wearing into the metal bars. Instead, I've designed covers that will protect the bars. An alternative would be plastic m4 washers, but that's a little more…
Safety toggle for the Xshot longshot to suit lefties. Recessed patterns you can colour for visual feedback. (acrylic model paint used in the cover photo) Print with the flat side touching the build plate, Should be fine without supports.…
The Xshot Longshot is horrendously overbarreled if you add a longer barrel without a 250+ fps spring. This fits an adjustable SCAR into the collet so the barrel can be kept to a minimum on sub 250fps setups while maintaining accuracy.…
Update 10/26/26 : Breech load version added to the files. Models are print oriented and do not require support. No blaster disassembly or modification required. Filament Elegoo PLA Plus (Red)
Extended the barrel to fit an extra ring of chains. Also made a sleeve to serve as a background to the chains. The sleeve prints in vase mode. It is a tight fit but it has to be so that the chains still fit around the barrel. The…
Wanted a mag holder on the rear so i combined these two models
If you do not like/want the stock to expand when pulled, and only expand when the lever is depressed, swap out the internal latch for this model. I did champfer one edge as a compatibility edit. There is a version without supports if you…
Used the Longshot stock by NIRODHA to find the butt sizing of the Longshot, so I could design a stock around it to replace the original one, namely a re-sized XZEUS stock. Then I realised that I'm actually pretty okay with the longshot…
A cap made for a Nerf Longshot CS-6 blaster. It is designed for the original spring that came with the blaster, and might not hold up if used with an aftermarket spring. Was printed in PLA, at 0.4 layer height. no supports necessary.
Have you ever wanted to put a Barricade muzzle in a Longshot? With these parts, it's now easier than ever! This is designed to print without added supports.
Using the Hyperion 2A aluminum heat-set insert QD sling mount, and several sizes of metric drill bits, you can add an extremely strong sling mount to your longshot, capable of withstanding the harshest play. You will need: Hyperion 2A QD…
Extended the lever so it is easier to use.
WARNING!!! This model does not include an air restrictor so you may need to add dampeners inside your plunger tube (basically try not to dry fire though I have a ton of times, it should be fine for the first 50 dry fires). I plan to…
Level up your X-Shot Longshot with this all-in-one front end designed for both performance and aesthetics. Tired of simple, flimsy, or ill-fitting designs? This isn't a remix—it's a complete redesign built from the ground up, blending the…
The hole is 3.7mm wide by 4.6mm deep. Make sure your inserts are about 1mm wider than the hole (so there's plastic to grip) and not as deep.
Wanted a mag holder on the rear so i combined these two models
If you do not like/want the stock to expand when pulled, and only expand when the lever is depressed, swap out the internal latch for this model. I did champfer one edge as a compatibility edit. There is a version without supports if you…
Using the Hyperion 2A aluminum heat-set insert QD sling mount, and several sizes of metric drill bits, you can add an extremely strong sling mount to your longshot, capable of withstanding the harshest play. You will need: Hyperion 2A QD…
Extended the barrel to fit an extra ring of chains. Also made a sleeve to serve as a background to the chains. The sleeve prints in vase mode. It is a tight fit but it has to be so that the chains still fit around the barrel. The…
This replacement pusher design aims to mitigate several jamming scenarios with the stock pusher on the XLS which may be caused by stacking tolerances, including: Darts getting stuck in the pusher ring Darts getting pulled backwards on…
