Magnetic Phone Stand for MagSafe and Pixelsnap — Qi2 Desk Holder, 4 or 6 Magnets, No Supports
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Magnetic desk stand for MagSafe, Pixelsnap or Qi2 phones. 4 or 6 magnets, no supports, tested not to tip.
- Ocena
- 0 / 5
- Polubienia
- 4
- Pobrania
- 8
- Wydruki
- 0
- Wyświetlenia
- 119
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Computers
- Licencja
- Creative Commons — Attribution
A magnetic phone stand that grows out of its own base.
Most MagSafe stands are a ring stuck on an arm stuck on a plate. This one is a single continuous surface: the ring is not glued onto the body, it is born from it. There is not one sharp edge anywhere on the part, because it was not built by gluing solids together — it was built as a distance field, so every junction is a tangent fillet.
What it works with
MagSafe — iPhone 12 and newer, with or without a MagSafe case
Pixelsnap — Pixel 10 / 10 Pro / 10 Pro XL
Qi2 — any phone or case with the standard Qi2 magnet ring
Any other phone — stick a magnetic ring on the back and you are done
The magnets sit on a 50 mm circle, which lines up with the standard MagSafe / Qi2 array.
Two versions
Magnetic-Phone-Stand-4-magnets.stl — 4 magnets. Sit on the diagonals, not in a cross. Cleaner look from the front.
Magnetic-Phone-Stand-6-magnets.stl — 6 magnets. Stronger hold. Pick this one for a heavy phone or a thick case.
Both use loose Ø10 × 5 mm neodymium cylinders — the cheapest and most common size there is. Four of them for the first version, six for the second. The pockets are 10.3 mm so they drop in without forcing.
It does not tip
This is where most magnetic stands fail. A phone is heavier than the stand: a Pixel 10 Pro is 207 g and this part is about 75 g. So the stability does not come from mass, it comes from putting the phone's centre of gravity well inside the footprint.
The foot reaches in front of the phone, and the ring is reclined to 52°. Measured with a 207 g phone mounted:
Tipping angle, forward: 41.7°
Tipping angle, sideways: 29.4°
Footprint: 112 x 76 mm
Height: 108 mm
Anything above 20° is comfortable. You can knock the desk and it stays put.
Prints without supports
Every downward-facing surface on this part is steeper than 45°. The only thing under that limit is the rounded outer rim of the ring, 5 cm² spread over strips of less than 1 cm² — that is the belly of a 3 mm fillet, the same thing your slicer prints on the underside of any rounded edge.
The ring is at 52° and not the usual 45° for exactly this reason: at 45° its back face sits right on the limit and half the slicers flag it.
Settings
No supports. No brim. Print it as it comes.
0.2 mm layers, 0.4 mm line width, 3 walls, 12% infill
~75 g and ~4 h in PLA
Set Z seam alignment to Random. On a surface this curved, an aligned seam reads as a scar down the spine of the fin.
Fitting the magnets
Print first, magnets after — the pockets open towards the phone, so nothing is trapped inside.
Read this before you glue anything. The magnet ring in your phone has alternating polarity. Hold each magnet against the back of the phone, find the face that pulls, mark it with a marker, and glue them all facing the same way. Get one backwards and it pushes instead of pulls. This matters more on the 4-magnet version, where there is less margin.
A drop of superglue in each pocket is enough.
Make it fit your magnets
The .py file is the model itself — it generates the STL, and every magnet dimension is a command-line flag:
python3 magnetic-phone-stand-parametric.py --imanes 6 --salida stand.stl
python3 magnetic-phone-stand-parametric.py --diam 8 --alto 3 --corona 54 --salida stand.stl
--imanes (default 4) — how many magnets
--diam (default 10) — magnet diameter, mm
--alto (default 5) — magnet height, mm
--corona (default 50) — diameter of the circle they sit on
--holgura (default 0.3) — pocket clearance
--paso (default 0.45) — mesh resolution, mm
Needs Python with numpy and scikit-image. It is not OpenSCAD: the shape is a signed distance field meshed with marching cubes, which is why the surface is continuous everywhere.
If your phone's magnet ring is not 50 mm, measure it: stick a piece of masking tape on the back, drop a magnet on it — it self-centres over one of the phone's magnets — and trace it. Do the same on the opposite side and measure centre to centre. Then pass that number to --corona.