1 / 17
140 mm Noctua inspired desk fan with built-in PWM controller — zdjęcie 1
1 / 17

140 mm Noctua inspired desk fan with built-in PWM controller

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

140 mm Noctua desk fan with integrated PWM speed controller in the base. Clean, compact, quiet and fully adjustable.

Ocena
5 / 5
Polubienia
352
Pobrania
321
Wydruki
2
Wyświetlenia
4696
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Office
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

A compact desk fan using a Noctua 140 mm PWM fan, with the PWM speed controller integrated directly into the base. The design keeps the fan setup clean and cable clutter to a minimum while allowing convenient speed adjustment directly at the desk. The sturdy base provides a stable footprint and houses the controller, making it a practical and customizable solution for a quiet, adjustable desktop fan.

This design of the airflow amplifier is inspired by of Noctua's original design and a remix of the files by nhchiu and Dmytro. The intake and the stand are my original designs.

The PWM speed controller is integrated directly into the base for convenient speed adjustment while keeping the setup clean and compact. The PWM PCB is a cheap version I found on AliExpress. I attached a photo of the board so you can find it, too.

One can basically install any 140 mm fan. Depending on the hub diameter, the fit may be slightly better or worse. I designed the intake and airflow amplifier for the Noctua NF-A14x25 G2 (see crossection). 

The stand is essentially the larger stand I designed for the 120 mm version. You can also use the smaller one included in the 120 mm version files, but I would not recommend it.

For assembly one will also need a few screws, nuts and washers, the PWM control board, a DC power jack, and a power supply (either USB or mains/Schuko to 12 V). To ensure an airtight seal, remove the rubber absorbers from the fan.

To get the original Noctua look I used Prusament PLA in Noctua Brown and Noctua Beige:
https://www.prusa3d.com/de/produkt/prusament-pla-noctua-brown-1kg-nfc/

I got the best results with Prusament PLA and the following settings:

  • Nozzle: Standard 0.4 mm

  • Layer height: 0.12 mm

  • Walls: 2 (4 can be used for additional stiffness, but may occasionally cause printing issues)

  • Infill: 35% Gyroid

  • Ironing: Off

  • Supports: Only required for the stand; all other parts can be printed without supports. Use normal support not tree support.

  • Brim: Normally not required, but recommended for the amplifier and the knob if additional bed adhesion is needed

  • Print speed: Up to 120 mm/s worked best for me; I recommend avoiding higher speeds for optimal print quality

Have a look at the 120 mm version, too:

Updates:

Amplifier V2.0: I redesign the amplifier so it's closer to the original design from Noctua. 

Amplifier V2.1: I recently updated the Airflow Amplifier to V2.1. Sometimes the inner section used to delaminate from the bed before it fused with the rest of the print. In V2.1, the walls of this inner section are slightly thicker, which helps prevent warping and delamination. If you still have trouble with the inner section try using a brim for this piece.

Knob: I added a two-color version of the knob. You can choose a different color for the layers of the arrow, so you can customize it while keeping filament waste to a minimum. I tinkered a little with the nob. The latest version is 2.9 and privides the best fit. I designed the knob to be a tight fit. However, depending on your material and print settings, it may end up being too loose or too tight. If necessary, try scaling the model by a few percent to adjust the fit.   

Tagi