1 / 8
Ada's Revenge - DIY eGPU enclosure for ADT-Link UT3G and ATX PSU — zdjęcie 1
1 / 8

Ada's Revenge - DIY eGPU enclosure for ADT-Link UT3G and ATX PSU

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Modular 3D printable enclosure for a DIY USB4 eGPU build using an ADT-Link UT3G, a full-size ATX power supply and a des

Ocena
0 / 5
Polubienia
2
Pobrania
14
Wydruki
0
Wyświetlenia
195
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial

Description

Ada's Revenge is a modular 3D printed enclosure for a DIY eGPU build based on the ADT-Link UT3G USB4 board, a desktop graphics card and a full-size ATX power supply.

The design is split into printable panels and structural sections so it can be assembled with screws, threaded inserts, aluminium M3 standoffs and magnets. No glue is required. The red side panels and fan filter provide airflow, while the front decorative panel is magnetically attached for easy removal.

Top 1/Top 2 and Bottom 1/Bottom 2 are bridged internally by six 100 mm long aluminium M3 female threaded standoffs. Each standoff is fastened from both ends, using 12 M3 x 10 mm screws in total. The section images show how the standoffs span the split structural panels and keep both halves aligned.

The printed fan-filter assembly has two parts: Fan Filter Inner and Fan Filter Outer. Cut the PVC filter mesh to fit and place it between the two printed parts before fitting the assembly over the 120 x 120 mm fan opening.

The Front.3mf project includes the Front frame plus four separate printed magnet holders. Front Deco.3mf includes the decorative panel plus four matching holders. Fit one 10 mm diameter x 3 mm thick magnet into each holder, for eight magnets total. Check all four opposing magnet pairs for attraction before seating the holders.

This release has been physically assembled and the enclosure BOM has been validated on the built unit.

Dimensions and hardware compatibility

- Nominal assembled enclosure envelope: approximately 358 mm deep x 220 mm  wide x 180 mm high. This is derived from the release 3MF geometry; a physical  enclosure measurement is still recommended before planning a tight space. - PSU used in the documented build: Tacens Radix VII AG 800 W. The published  dimensions for part 1RVIIAG800 are 150 mm wide x 157 mm deep x 85 mm high.  

Confirm the label on your unit: the similarly named 800M is a different  revision and is listed as 160 mm deep.

- Fan opening and hardware: one nominal 120 x 120 mm PC case fan. Fan thickness  and connector are not constrained by the published BOM.

- This is a component-specific release. Compatibility with another GPU, PSU or  eGPU controller is not guaranteed from nominal form factor alone.

See docs/DIMENSIONS.md for individual 3MF bounding boxes and measurement status.

Important: this is an eGPU enclosure around PC power hardware. Do not open or modify a power supply, do not work on the enclosure while it is connected to mains power, and keep proper grounding, strain relief and electrical protection in place. A printed enclosure does not replace certified electrical safety features.

## Printing

The included g-code files are for Prusa MK3S, a 0.4 mm nozzle, 0.2 mm layer height and 15% infill. They are provided as the validated build profile used for this release. For any other printer, material or dimensional variant, slice the 3MF files again.

Approximate filament use from the included g-code:

- PETG: 844.09 g

- PLA: 203.34 g

- Total: 1047.43 g

- Combined estimated print time: 72 h 8 min 38 s

Three physical side panels use slicer modifiers with zero top and bottom layers: one Left 2 / L2 panel and two copies of Right / R. This exposes the infill as an airflow grille, as shown in the photos and section images. Keep those modifiers if you re-slice the 3MF files. The Right x 2 3MF and g-code contain one panel; print or run that file twice.

## Files included

3MF model files:

- 3mf/Bottom 1.3mf

- 3mf/Bottom 2.3mf

- 3mf/Fan Filter Inner.3mf

- 3mf/Fan Filter Outer.3mf

- 3mf/Front Deco.3mf

- 3mf/Front.3mf

- 3mf/Left 1.3mf

- 3mf/Left 2.3mf

- 3mf/Rear.3mf

- 3mf/Right x 2.3mf - print 2

- 3mf/Sep.3mf

- 3mf/Top 1.3mf

- 3mf/Top 2.3mf

Supporting files:

- docs/BOM.md

- docs/ASSEMBLY.md

- docs/DIMENSIONS.md

- docs/FILE_MANIFEST.md

## BOM

See docs/BOM.md.

## Assembly

See docs/ASSEMBLY.md.

Tagi