1 / 5
Hulk Fist Pencil Holder — Solid Desk Organizer, Holds 5 Pencils — zdjęcie 1
1 / 5

Hulk Fist Pencil Holder — Solid Desk Organizer, Holds 5 Pencils

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

The Hulk's fist gripping your pencils instead of a glass.

Ocena
0 / 5
Polubienia
8
Pobrania
16
Wydruki
0
Wyświetlenia
87
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Office
Licencja
GNU General Public License v2.0

The Hulk's fist, gripping your pencils instead of a glass.

This is a remix, and here is exactly what changed

The sculpt is not mine. It is Qwerty's Hulk's Fist wall lamp, published under GPL v2.0 — the knuckles, tendons and veins are all theirs. What I did was turn it into a working desk object, and every change came out of a measurement rather than a guess:

Reoriented so the grip is vertical. In a fist, the tube your fingers form — the one a glass would pass through — runs parallel to the row of knuckles, not along the forearm. Rotating the model so that axis stands vertical puts the forearm horizontal and the thumb on top: the pose of a hand holding a cup.

The lamp flange is gone. The original mounts on a wall through a flat plate with three screw holes. Cutting it leaves the wrist open, which is where the base goes anyway.

The bore is in the grip valley, not in the thickest part. This one took two attempts. Searching for the axis with the most material around it finds the mass of the palm, and the hole came out through the back of the hand. The right spot shows up in a height map of the surface: between the fingers and the thumb the skin drops to z=37 while everything around it sits at 46-48 — a 10 mm depression. That hollow is the grip valley, it has 21 mm of flesh around it, and a 28 mm bore exits exactly where the rim of a glass would.

The base is cut by tipping angle, not by area. Cutting flat 4 mm up from the lowest point gave 18.5 cm2 of footprint and a tipping angle of only 14 degrees — it falls over if you nudge it. Going 10 mm deeper:

  • 4 mm up: 18.5 cm2 footprint, tips at 14°

  • 10 mm up: 25.5 cm2 footprint, tips at 22°

  • 14 mm up: 33.3 cm2 footprint, tips at 36° — the sweet spot

  • 18 mm up: 48.8 cm2 footprint, tips at 41°

14 mm is the sweet spot. Going deeper buys 5 more degrees and costs 4 mm of height. And it had a side effect worth more than the stability: the sub-45° overhang dropped from 58 cm2 to 18 cm2, because the deeper cut removed the belly of the forearm — which was half the support problem.

And it is solid on purpose. An earlier version was hollowed with a 2.6 mm shell computed by voxel erosion. That was wasted work: the slicer already hollows the model with infill, and it does it better — uniform walls, whatever perimeter count you ask for, and no risk of the cavity breaking through the skin. Deleting the cavity took the model from 114,000 triangles to 33,000 and the CSG from three minutes to sixteen seconds.

Verified, not hoped

  • Watertight: 1 piece, 0 open edges

  • Size: 87 x 107 x 94 mm

  • Flat base: 31.1 cm2

  • Tipping angle, empty: 36° (about 30° loaded with pencils)

  • Bore: 28 mm, 46 mm deep, wall 7 mm

  • Overhang under 45°: 18.3 cm2

  • Solid volume: 453 cm3

Print settings

  • Supports: yes, but light. 18 cm2 of overhang, most of it in the lowest 16 mm at about 31° — the underside of the forearm and the little-finger edge. Tree supports on that band are enough; you do not need them over the whole model.

  • 0.2 mm layers, 3 walls, 10-15 % infill. It is a big solid: about 120-170 g depending on infill.

  • No brim needed with 31 cm2 of base, but it does not hurt.

  • Print it in green. Obviously.

If it is too big or too long: do not scale the STL, regenerate it. Scaling shrinks the bore with everything else — at 75 % the 28 mm hole becomes 21 mm. The included script keeps the bore absolute while changing the fist size. The limit at each scale, keeping 2.5 mm of wall:

  • 100 % scale: 94 mm height, 37 mm max bore, 30 pencils

  • 85 % scale: 80 mm height, 31 mm max bore, 20 pencils

  • 75 % scale: 70 mm height, 26 mm max bore, 15 pencils

  • 65 % scale: 61 mm height, 22 mm max bore, 11 pencils

Files, and what GPL v2.0 requires

The GPL asks for the source, so it is all here:

  • hulk-fist-pencil-holder.scad — the cuts and the bore

  • orient_and_measure.py — reorients the original mesh and measures the grip valley

  • inspect_mesh.py — checks any STL: piece count, watertightness, flat base area, overhang area

Anything you build from this stays GPL v2.0.

Credit

Original sculpt: Qwerty — Hulk's Fist from the wall - lamp, GPL v2.0. Go and like their model; the hard part is theirs.

Hulk is a Marvel character. This is fan-made and not affiliated with or endorsed by Marvel or Disney.

Tagi