CNC Pubbox M V1.0 for VESC XR/Funwheel

This XR-form-factor controller box provides numerous controller mounts and plenty of room for activities.

CNC Pubbox M V1.0 brings the following new, main features:

• Switchcraft port is moved to the opposite side for maximum space in the box

• Battery harness port is moved toward the wheel for the maximum space in the box

• New LED window cover design, recessed with a lip to improve sealing and allow for a thicker window piece

Along with the existing changes since Pubbox 3.0:

• Angled footpad and battery harness mount points, to help with pushing the battery harness into the rail and to allow more clearance for the footpad connector

• Threaded battery harness hole, M20. No more inner nut needed, just thread it in.

• Now, the box has full contact with the rails at both screw points. No more tab spacers needed for the bumpers (which also means bumpers with these tabs will need them removed).

• 23% less lid screws!

Built-in mount threaded screw mounts compatible with several VESC controllers for a range of options:

• Thor300/Thor400/JF6

• Mk8/Mk8 Pro

• Lfoc

• Tronic X12

Adapters and plates are available for:

• Ubox 85v

• ...and more

Can fit 2s2p 21700 Split pack depending on size of VESC you use.

If you install an X12, you must remove its original mounting plate and use its 4 center holes to install and PLEASE install a NEW 1mm thick Thermal Pad AND MOSFET Spacer between the box floor and X12 (https://makerworld.com/en/models/543493). This will prevent any shorting on the MOSFETS which is sadly not already included on the original X12. 

Compatible with the Superflux Plug on the Motor Cable Side
Compatible with Genuine Switchcraft Port for use with stock XR Footpads

MUST USE 19x1 Threaded Button AND GX16x1 Charge Port (This means a 19mm diameter button with 1mm thread pitch and 16mm diameter port with 1mm thread pitch (choose whatever pin count you need), usually specified somewhere on the product listing)

Printed Parts Recommend Materials

• PETG-CF, PETG, or comparable: LED Clips, connector covers

• TPU 95a: Gasket, sealing parts

CNC'ed Parts Recommend Materials

• 6061 aluminum: Box, lid (optionally), heat sink

• Polycarbonate: Window, lid (optionally)

Parts List for Basic Box

• 1 x Box

• 1 x Lid

• 1 x LED Window

• 1 x Gasket

• 1 x Connector Cover

• 4 x #10-32 ¾" long bolts (Countersunk/Flat-Top): https://www.aliexpress.us/item/3256805313365660.html

• 1 x Switchcraft Footpad Connector: https://www.digikey.com/en/products/detail/switchcraft-inc/EN3P6MX/2080472 and https://www.digikey.com/en/products/detail/switchcraft-inc/EN3C6FX/2080462

• 1 x M20 Gland for Battery Side: https://www.aliexpress.us/item/2255800865722468.html

• 1 x Fungineers Superflux Connector OR 1 x M20 Gland for Motor Side

• 1 x 19x1 Power Button https://www.aliexpress.us/item/3256806411255119.html

• 1 x GX16-4 Charge Port https://www.aliexpress.us/item/3256804459446780.html

• 3 x M3 12mm long bolts for LED Heat Sink (Countersunk/Flat-Top): https://www.aliexpress.us/item/2251832812303109.html

• 24 x M3 8mm long bolts for Lid (Countersunk/Flat-Top): https://www.aliexpress.us/item/2251832812303109.html