1 / 10
Zemismart ZM25EL 30mm/32mm Roller Shade Tube Adapters — zdjęcie 1
1 / 10

Zemismart ZM25EL 30mm/32mm Roller Shade Tube Adapters

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Replacement drive gear and end cap adapters to fit a Zemismart ZM25EL into a 30mm ID/32mm OD roller shade tube

Ocena
0 / 5
Polubienia
1
Pobrania
6
Wydruki
0
Wyświetlenia
54
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Home Decor
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

TL;DR

This is a set of adapters that allows you to fit a Zemismart ZM25EL tubular motor to a 30mm inner diameter (32-33mm outer) roller shade tube, instead of the 37-38mm tubes they are originally designed for. Assembly is very easy and needs just a screwdriver or pliers to remove and replace a single clip.

Use Case

My house has a wide (76") patio door roller shade from Bali with a 30mm inner diameter (32-33mm OD) aluminum tube. I really wanted to retrofit a smart motor to this set up, and prefer battery-powered to reduce cords and Zigbee to fit into my existing mesh... but unfortunately I couldn't find exactly this combination to buy. The wide patio door shade weighs about 5 lb, which exceeded the weight limits for Zemismart's 16mm core motors, otherwise I could have used @chaoscontrol's ZM16EL adapters:

So I did some photo-based reconnaissance, took a gamble, and purchased the US sub-brand "Blindsmart" ZM25EL off Amazon to take it apart and design my own adapters.

It ended up working great!

Printing

You need:

  • One drive gear - attaches to the far end of the motor and actually rotates the tube

  • One end cap - attaches to the near end of the motor but spins freely as the tube rotates, keeping the motor centered

  • Your own solution for the axle at the far end of the tube - I was able to leverage my existing factory axle in the Zemismart bracket, so I did not design a 30mm replacement.

Print Settings:

  • Material

    • I used ASA for strength, though I suspect PETG would work fine as well.

    • The end cap in particular has some very thin joints, but it should not bear much actual torque as it is only used to center the motor.

    • The drive gear is quite solid and should be fine in PETG.

  • Supports

    • Drive gear: None

    • End cap: Standard supports on build plate. There is a recessed circular plate to hold up. I left this as profile default ("Snug", rectilinear) for Prusament ASA on a CORE One L.

  • Perimeters and Infill

    • I used 10 perimeters and 100% infill for a really strong part, though I suspect this is overkill. In any case both pieces together used only about 6 grams of filament fully solid.

  • Layers

    • I printed with 0.15mm STRUCTURAL settings, though 0.2mm would likely be just fine as well.

    • Default top & bottom solid layers 

Assembly

Follow the pictures here in order:

  1. Use a pliers or screwdriver to remove the clip from the end of the motor, then slide off the factory 37mm gear and the factory 37mm end cap. Note that both fit quite snugly, but other than the clip at the end they do slide off with some effort.

  2. Photo [A] - print the 30mm drive gear and end cap

  3. Photo [B] - Under the factory end cap is a little white free-spinning collar. Leave this attached, as the new 30mm end cap will slide over top of it.

  4. Photo [C] - Orient the 30mm end cap so that the teeth will point into the tube and the widest ridge is up against the outside: this widest edge will not side into the shade tube and can be seen in the last pictures below. Slide the end cap along the entire motor and align it with the fins of the factory collar. It's a snug fit but should slide all the way on until the recessed circle on the new end cap fully overlaps the ridge of the white collar, and the whole thing spins freely together.

  5. Photo [D] - Orient the drive gear in either direction (it's symmetric) and slide it on to the motor shaft. Then clip it in place with the factory clip. This gear is a very tight fit, and I actually had to file mine down very slightly, then push with some force to install it. If you're not able to fit it, let me know and I'll publish a version with more tolerance.

  6. Photo [E] - Ensure the metal clip is installed to lock the gear in place.

  7. Photo [F] - Verify full assembly looks like this:

  8. Photo [G] - Inspect your tube and find the internal ribs to align with. 
    Note: if your tube doesn't match this, let me know and I'm happy to try and sketch another variation of the drive gear to suit your tube shape!

  9. Photo [H] - Align the drive gear with the ribs and insert the motor into the tube.

  10. Photo [I] - Align the end cap with the ribs as well, and continue inserting the motor.

  11. Photo [J] - Continue inserting the motor until the roller tube reaches the widest ridge of the end cap. (Note the end cap ridge in black, here.)

  12. Install your blind to the wall using your existing or Zemismart's new mounts!

Notes:

  • This project was inspired by the 30mm hardwired wifi blind motor (ZM25RX-11-35-30) that Zemismart sells, and especially by the Zigbee variant (ZM25RZ01-30) that they seem to have stopped producing.... but which was the product I actually wanted to buy. If those are available to you or otherwise meet your needs, they might save a bit of printing and assembly work! 😀

  • These adapters MIGHT also work with other 25mm-core tubular motors from Zemismart, e.g. Matter motors MT25A or MT25B, or Wifi motors like ZM25WB, but I have not tested them. Please report in the comments if you do!

Tagi