1 / 4
Running Twins – Same Size, Same Weight, One Always Wins — zdjęcie 1
1 / 4

Running Twins – Same Size, Same Weight, One Always Wins

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Two twin rollers race down a ramp: same size, same weight to the gram, same start line, one PUSH bar.

Ocena
0 / 5
Polubienia
8
Pobrania
11
Wydruki
0
Wyświetlenia
275
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Public Domain

Two identical rollers. One always wins.

Meet Castor and Pollux, the Running Twins. Same diameter, same length, same weight – put them on a kitchen scale, they match to the gram. Roll them both against the PUSH bar, press, and watch: Castor pulls ahead. Every time.

Swap lanes: Castor wins. Turn them end for end: Castor wins. Let the most suspicious kid in the room pick the lane, the roller, the order: Castor wins.

There is no motor, no magnet, no spring, no weight that shifts around inside. The whole thing runs on gravity and nothing else. The secret is hiding in plain sight, and I explain it in the very last section of this page. Don't scroll there yet – let people guess first. Most adults get it wrong.

How to run the race

  1. Hand the twins to the audience. Let someone weigh them, measure them, roll them on the table.

  2. Let the audience choose which roller goes in which lane.

  3. Roll both twins against the PUSH bar. The bar is the start line: both rollers are aligned to the same edge, automatically.

  4. Press PUSH. Watch.

  5. Swap lanes. Press again. Ask them to explain it.

Printing

No supports on any part. Every piece sits on a flat face.

Part

Orientation

Infill

Material

Starting block halves

Flat face down

15 % gyroid

PLA

PUSH bar

Flat, as placed

15 %

PLA

Castor / Pollux

Standing on an end face

100%

PLA, same spool !

Notes that matter:

  • Print both rollers from the same spool, in the same session. Colour, surface and weight must match. Use the .3mf files.

  • After printing, weigh the twins. The design targets equal mass; extrusion variance can leave 1–2 g difference. A trim pocket under each end cap accepts [a small washer / a coin] – add it at the same place on either twin until the scale agrees.

Assembly (about 10 seconds)

  1. Starting block: join the two halves with the two printed keys. Press fit. A drop of glue is optional.

  2. PUSH bar: drop it into its channel. It must slide freely and return on its own. If it does not, see the note above.

  3. Deck: connect the ramp sections [dovetails / keys], then clip the starting block onto the top section.

  4. Twins: fit the end caps, weigh both rollers, trim if needed.

SPOILER – How it actually works

Stop here if you want to figure it out yourself. Seriously, try the swap test first.

Castor and Pollux have exactly the same mass – but not in the same place. Inside Castor, the material is packed close to the axis, with a thin outer shell. Inside Pollux, the same amount of material is pushed out to the outer shell, with an empty centre. Both volumes were matched in CAD to the cubic millimetre, which is why they weigh the same and why the .3mf files use different settings for each twin.

On a slope, gravity's energy is split between two jobs: moving the roller forward and spinning it. Material far from the axis has to travel a long way around for every turn, so it is expensive to spin. Pollux "wastes" a large share of its energy on rotation and has less left for the descent. Castor barely spins its light shell and puts almost everything into going forward. Same mass, same slope, same start – a different share of energy, so a different acceleration.

It is the same physics as a figure skater pulling in her arms to spin faster.

Nothing is hidden except a distribution of mass, and the swap test proves that the ramp is fair.

Tagi