1 / 5
Bleeder for Large Clipper Lighters - Metal and Plastik — zdjęcie 1
1 / 5

Bleeder for Large Clipper Lighters - Metal and Plastik

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Solves Problems when only getting a very small Flame out of your Lighter. If you like, please rate and share makes.

Ocena
0 / 5
Polubienia
2
Pobrania
4
Wydruki
0
Wyświetlenia
52
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

I didnt like fiddling around with the fillervalve to much, thats why I came up with this Bleeder....

Here is your step-by-step guide to perfectly refilling your Clipper lighter.

🛠 What You Need

  • An empty Clipper lighter

  • A can of butane gas

  • The purging tool that you downloaded here....

📋 Step-by-Step Instructions

1. Purge the Lighter (Bleeding)

  • Place your Clipper Lighter in the Bleeder, as shown in the pictures.

  • Best just let it stand for some time/minutes, in the orientation shown in the pictures.

  • Keep it in the Bleeder until the hissing sound completely stops and no more residual air or gas escapes.

  • Why? Trapped air blocks the space for fresh gas. Without purging, the tank will not fill up completely.

2. Cool Down the Lighter

  • Place the purged Clipper lighter into the refrigerator for about 5 to 10 minutes (do not put it in the freezer).

  • Why? The cold temperature causes the inside temperature to drop, creating a pressure difference between the cold lighter and the warm gas can. This allows the new gas to flow in effortlessly.

3. Refill the Gas

  • Take the cold lighter out of the fridge and hold it upside down (valve pointing downwards).

  • Shake the butane gas can briefly and press it vertically upside down onto the valve.

  • Press the gas can down with firm, steady pressure for about 3 to 5 seconds.

4. Warm Up and Test

  • Let the lighter sit for 1 to 2 minutes so it can return to room temperature..

⚠ Safety Warning: First time lighting may cause a very large flame !!!

⚠ Safety Warning: Never perform this process near open flames or hot surfaces, and ensure the room is well-ventilated.

_______________________________________________________________________________________________________________

Ich wollte zum Entlüften möglichst wenig am Einfüllventil herum manipulieren müssen, daher habe ich mir diesen Entlüfter gemacht...

Hier ist deine Schritt-für-Schritt-Anleitung, um dein Clipper-Feuerzeug optimal nachzufüllen.

🛠 Was du brauchst

  • Ein leeres Clipper-Feuerzeug

  • Eine Dose gereinigtes Feuerzeuggas

  • Einen Entlüfter den du her runterladen kannst

📋 Schritt-für-Schritt-Anleitung

1. Das Feuerzeug entlüften

  • Dein Clipper Feuerzeug in den Entlüfter setzen, so wie auf den Bildern gezeigt.

  • Den Entlüfter mit dem Feuerzeug senkrecht stellen...

  • ...bis das Zischen komplett aufhört und kein Restgas mehr entweicht.

  • Warum? Eingeschlossene Luft blockiert den Platz für frisches Gas. Ohne Entlüften wird der Tank nicht richtig voll.

2. Das Feuerzeug abkühlen

  • Lege das entlüftete Clipper-Feuerzeug für ca. 5 bis 10 Minuten in den Kühlschrank (nicht ins Gefrierfach).

  • Warum? Durch die Kälte zieht sich das verbleibende Gas im Inneren zusammen. Es entsteht ein Druckunterschied zur warmen Gasflasche, wodurch das neue Gas später viel leichter hineinfließt.

3. Das Gas auffüllen

  • Nimm das kalte Feuerzeug aus dem Kühlschrank und halte es über Kopf (Ventil zeigt nach unten).

  • Schüttle die Butangasflasche kurz und setze sie ebenfalls senkrecht über Kopf auf das Ventil.

  • Drücke die Gasflasche mit festem, gleichmäßigem Druck für ca. 3 bis 5 Sekunden nach unten.

4. Aufwärmen und Testen

  • Lass das Feuerzeug eine Zeit lang ruhen, damit es wieder Zimmertemperatur annimmt.

  • Zünde das Clipper erst an, wenn es sich erwärmt hat – vorher ist der Druck zu niedrig für eine stabile Flamme.

⚠ Sicherheitshinweis: Nach dieser Befüllmethode bitte beachten das die ersten Flammen recht hoch sein können.

⚠ Sicherheitshinweis: Führe den Vorgang niemals in der Nähe von offenem Feuer durch und sorge für gute Belüftung.

Tagi