1 / 3
BITUXX Shower Drain Grate Remix — Full-Depth Hair Catcher, Wide Slots, Pull Handle — zdjęcie 1
1 / 3

BITUXX Shower Drain Grate Remix — Full-Depth Hair Catcher, Wide Slots, Pull Handle

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Remix of Hooch's BITUXX shower drain grate: 43.4% open area instead of 36.1% (23 wide slots instead of 146 small holes),

Ocena
0 / 5
Polubienia
0
Pobrania
2
Wydruki
1
Wyświetlenia
21
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Bathroom
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This is a from-scratch redesign of BITUXX Shower Drain Grate by Hooch, built to drop into the same drain: identical 115 × 64 mm outline, notch, legs, foot pads and M3 handle bosses, reproduced from the original mesh to within 0.06 mm. What's underneath is new — bigger openings, a hair catcher that actually runs the full depth of the drain, and a handle you don't need a drill for.

Why remix it

The original's own instructions tell you to drill out the 3.5 mm holes with a 3.5 mm bit if you want better flow, and there's no hair catcher below the top plate at all — just the holes. This version fixes both without a drill: fewer, larger, chamfered openings for flow, and a lattice built into the legs that catches hair before it reaches the trap and lifts straight out with the grate.

What's different from the original

  • Openings: 23 chamfered stadium-shaped slots (5 mm wide) instead of 146 small holes. Open area is 43.4% versus the original's 36.1%, and every individual opening is markedly larger than one original hole, so hair and scum can no longer bridge it by surface tension the way they do across a 3.5 mm hole.

  • Hair catcher: a lattice of 60 pins runs the entire drain depth, to 1 mm above the leg tips, tied together by rungs at four heights on the way down. Every slot has a screen directly behind it, and nothing in the lattice is narrower than 3.5 mm, so slime and grit still pass straight through — only hair gets caught, all the way to the floor of the drain, not just under the top plate.

  • Side lattice: two pin columns per wing with cross rungs between them, at least as fine a mesh as the main field. This was the weak point of an earlier pass at this remix and is fixed here.

  • Handle: bolts on with the same 2 × M3 hardware the original's handle uses, no drilling required, and gives about 11 mm of finger clearance to lift the whole assembly — grate and lattice together — straight up for cleaning.

  • The underside is one connected frame now (the rungs tie into the legs), noticeably stiffer than the original's flat 3 mm plate despite the much larger openings.

Fit — check these against your drain before printing

  • Needs at least ~27 mm of clear depth under the grate across the whole footprint (the lattice reaches to 1 mm above the leg tips). If your trap housing intrudes higher than that, shorten the lattice depth.

  • Needs at least ~16 mm clear above the top face for the handle. If a shower tray or cover sits closer, shorten the handle height — even a 10 mm bar still gives a usable fingertip hook.

  • 5 mm slots are hand/foot-safe by the usual grate convention, but a ring can pass edge-on where the original's 3.5 mm holes wouldn't; the lattice underneath usually still catches it, but not guaranteed. Narrow the slot width if that matters for your household.

Print settings

  • Orientation: grate top-face-down on the bed, lattice printing upward; handle lying on its side. No supports needed either way — every pin flares from a wide base and no overhang exceeds 45° except the intentionally flared pin tips.

  • 0.2 mm layers, 2 perimeters (bars, pins and rungs are 4 line-widths wide at 0.45 mm), 3 top/bottom layers, elephant-foot compensation on — the first layer is the visible top surface.

  • Material: PETG or ASA. This sits in hot, soapy water regularly and PLA will creep over time.

  • Retraction and 0.2 mm z-hop on, "avoid crossing perimeters" on — there are 64 slender freestanding features (60 hair-catching pins plus the 4 legs). Print the top ~10 mm of the lattice at 60 mm/s or slower for cleaner towers.

  • By volume, not sliced: 28.6 cm³ (grate) + 4.7 cm³ (handle) ≈ 33.3 cm³ combined — roughly 35 g in ASA or 42 g in PETG at typical filament density, before brim.

Cleaning

Lift the whole thing out by the handle, pull the hair off the rungs, rinse, drop it back in.

Files

  • grate.stl / grate.3mf — the grate on its own, ready to slice.

  • handle.stl — the handle, already oriented for printing on its side.

  • grate_v2_plate.3mf — both parts placed on one plate with clearance between them.

  • grate_v2.py — the parametric generator (Python: numpy, shapely, trimesh, manifold3d), for anyone who wants to adapt this to a different drain rather than print it as-is.

Making it fit a different drain

Everything here comes from a parameter file, not a hand-built model. The parameters most people will want: slot_w (opening width, 5 mm here), pin_len (lattice depth, 26 mm here), rung_pitch (rung spacing, 6.5 mm here), wing_ladder (the two-column side lattice, on here), handle_h (handle clearance, 15 mm here). Change any of them and re-run the script to regenerate every STL.

Tagi