1 / 3
BITUXX Shower Drain Grate Remix — Full-Depth Hair Catcher, Wide Slots, Pull Handle — image 1
1 / 3

BITUXX Shower Drain Grate Remix — Full-Depth Hair Catcher, Wide Slots, Pull Handle

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Remix of Hooch's BITUXX shower drain grate: 43.4% open area instead of 36.1% (23 wide slots instead of 146 small holes),

Rating
0 / 5
Likes
0
Downloads
2
Makes
1
Views
21
Reviews
0

Updated at source:

Model information

Category
Bathroom
License
Creative Commons — Attribution — Noncommercial — Share Alike

This is a from-scratch redesign of BITUXX Shower Drain Grate by Hooch, built to drop into the same drain: identical 115 × 64 mm outline, notch, legs, foot pads and M3 handle bosses, reproduced from the original mesh to within 0.06 mm. What's underneath is new — bigger openings, a hair catcher that actually runs the full depth of the drain, and a handle you don't need a drill for.

Why remix it

The original's own instructions tell you to drill out the 3.5 mm holes with a 3.5 mm bit if you want better flow, and there's no hair catcher below the top plate at all — just the holes. This version fixes both without a drill: fewer, larger, chamfered openings for flow, and a lattice built into the legs that catches hair before it reaches the trap and lifts straight out with the grate.

What's different from the original

  • Openings: 23 chamfered stadium-shaped slots (5 mm wide) instead of 146 small holes. Open area is 43.4% versus the original's 36.1%, and every individual opening is markedly larger than one original hole, so hair and scum can no longer bridge it by surface tension the way they do across a 3.5 mm hole.

  • Hair catcher: a lattice of 60 pins runs the entire drain depth, to 1 mm above the leg tips, tied together by rungs at four heights on the way down. Every slot has a screen directly behind it, and nothing in the lattice is narrower than 3.5 mm, so slime and grit still pass straight through — only hair gets caught, all the way to the floor of the drain, not just under the top plate.

  • Side lattice: two pin columns per wing with cross rungs between them, at least as fine a mesh as the main field. This was the weak point of an earlier pass at this remix and is fixed here.

  • Handle: bolts on with the same 2 × M3 hardware the original's handle uses, no drilling required, and gives about 11 mm of finger clearance to lift the whole assembly — grate and lattice together — straight up for cleaning.

  • The underside is one connected frame now (the rungs tie into the legs), noticeably stiffer than the original's flat 3 mm plate despite the much larger openings.

Fit — check these against your drain before printing

  • Needs at least ~27 mm of clear depth under the grate across the whole footprint (the lattice reaches to 1 mm above the leg tips). If your trap housing intrudes higher than that, shorten the lattice depth.

  • Needs at least ~16 mm clear above the top face for the handle. If a shower tray or cover sits closer, shorten the handle height — even a 10 mm bar still gives a usable fingertip hook.

  • 5 mm slots are hand/foot-safe by the usual grate convention, but a ring can pass edge-on where the original's 3.5 mm holes wouldn't; the lattice underneath usually still catches it, but not guaranteed. Narrow the slot width if that matters for your household.

Print settings

  • Orientation: grate top-face-down on the bed, lattice printing upward; handle lying on its side. No supports needed either way — every pin flares from a wide base and no overhang exceeds 45° except the intentionally flared pin tips.

  • 0.2 mm layers, 2 perimeters (bars, pins and rungs are 4 line-widths wide at 0.45 mm), 3 top/bottom layers, elephant-foot compensation on — the first layer is the visible top surface.

  • Material: PETG or ASA. This sits in hot, soapy water regularly and PLA will creep over time.

  • Retraction and 0.2 mm z-hop on, "avoid crossing perimeters" on — there are 64 slender freestanding features (60 hair-catching pins plus the 4 legs). Print the top ~10 mm of the lattice at 60 mm/s or slower for cleaner towers.

  • By volume, not sliced: 28.6 cm³ (grate) + 4.7 cm³ (handle) ≈ 33.3 cm³ combined — roughly 35 g in ASA or 42 g in PETG at typical filament density, before brim.

Cleaning

Lift the whole thing out by the handle, pull the hair off the rungs, rinse, drop it back in.

Files

  • grate.stl / grate.3mf — the grate on its own, ready to slice.

  • handle.stl — the handle, already oriented for printing on its side.

  • grate_v2_plate.3mf — both parts placed on one plate with clearance between them.

  • grate_v2.py — the parametric generator (Python: numpy, shapely, trimesh, manifold3d), for anyone who wants to adapt this to a different drain rather than print it as-is.

Making it fit a different drain

Everything here comes from a parameter file, not a hand-built model. The parameters most people will want: slot_w (opening width, 5 mm here), pin_len (lattice depth, 26 mm here), rung_pitch (rung spacing, 6.5 mm here), wing_ladder (the two-column side lattice, on here), handle_h (handle clearance, 15 mm here). Change any of them and re-run the script to regenerate every STL.

Tags