Fidget Pumpkin

The "Keeps Your Hands Busy" Fidget Pumpkin 🎃

A fidget toy for your desk. It sits flat as a pumpkin, and every way you move the stem gives it a different look.

🟩 𝗪𝗔𝗬𝗦 𝗧𝗢 𝗣𝗟𝗔𝗬

▸ 𝗧𝘄𝗶𝘀𝘁 𝘁𝗵𝗲 𝗦𝘁𝗲𝗺 — Leave it flat on the desk and twist. The rings shift against each other into mesmerizing designs.

▸ 𝗣𝘂𝘀𝗵 𝗮𝗻𝗱 𝗣𝘂𝗹𝗹 — Slide the stem from side to side and the rings ripple off-center for a whole different set of visuals.

▸ 𝗟𝗶𝗳𝘁 𝗜𝘁 𝗨𝗽 — Raise it by the stem and the 18 rings drop into a scalloped cone.

▸ 𝗛𝗲𝗮𝗿 𝗜𝘁 𝗦𝗲𝘁𝘁𝗹𝗲 — Raise and lower it on the desk and it makes a satisfying sound as the rings come back down.

▸ 𝗧𝗲𝘅𝘁𝘂𝗿𝗲𝗱 𝗦𝘁𝗲𝗺 — The stem is textured, so it has a tactile feel under your fingers while you fidget.

🟩 𝗪𝗛𝗔𝗧 𝗠𝗔𝗞𝗘𝗦 𝗜𝗧 𝗪𝗢𝗥𝗞

▸ 𝗣𝗿𝗶𝗻𝘁𝘀 𝗶𝗻 𝗣𝗹𝗮𝗰𝗲 — One print, no assembly. All 18 rings and the stem come off the plate already captured inside each other.

▸ 𝗧𝘂𝗻𝗲𝗱 𝗚𝗮𝗽𝘀 — The gap between rings grows from about 1mm at the stem to about 2mm at the rim, so the outer rings still move freely instead of binding up.

▸ 𝗦𝘁𝗮𝘆𝘀 𝗧𝗼𝗴𝗲𝘁𝗵𝗲𝗿 — The ring walls are angled so each ring stays captured by its neighbors while you twist, slide and lift it.

▸ 𝗧𝗵𝗿𝗲𝗲 𝗖𝗼𝗹𝗼𝗿𝘀, 𝗧𝘄𝗼 𝗦𝘄𝗮𝗽𝘀 — Black ring bodies, orange faces and a brown stem, for only two filament changes and under 3g of purge.

🟩 𝗖𝗛𝗘𝗖𝗞 𝗬𝗢𝗨𝗥 𝗕𝗘𝗗 𝗙𝗜𝗥𝗦𝗧

▸ 179 x 174mm across and 45mm tall with the stem. Leave room beside it for the prime tower if you print it in color.

🟩 𝗣𝗥𝗜𝗡𝗧 𝗦𝗘𝗧𝗧𝗜𝗡𝗚𝗦

No supports required · no brim · 0.20mm layer height · 2 walls · 10% grid infill · PLA

Printed on a Creality Hi 2 in 5h 2m and 127g. Happy fidgeting! 🎃