1 / 7
SCX24 LCG Motor mount for 9mm screw distance motors up to 12mm (1224)
Zamów wydruk tego modelu
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
SCX24 LCG Motor mount for small 12mm motorsStock or aftermarket gear and bearings can be used (Note: While testing…
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 8
- Wydruki
- 0
- Wyświetlenia
- 44
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- RC & Robotics
- Licencja
- Creative Commons — Attribution — Noncommercial
- SCX24 LCG Motor mount for small 12mm motors
- Stock or aftermarket gear and bearings can be used (Note: While testing different gear and bearings from different aftermarket gearboxes I've seen there is quite some difference in tolerance. Let me know if there is too much play between spur and idler gear and I'll upload more boxes with different tolerances)
- Custom skid plates provided and required to mount the transmission (I hope at least one suits you)
- Well there is not much material left but I tried my best to find a way having the motor similar as the stock motor
- Friendly to print while only the lid requires small support
- Motor center sits about 11mm above skid plate and provides hopefully sufficient clearance to axle depending on your setup
Cons:
- Bulkier compared to stock gearbox
- Different screws required
- Specific skid plates required (provided)
- fiddly design with smal tolerances
Pros:
- Motor position similar to stock motor
- Motor center sits about 11mm above skid plate
- 0.5mm lower Axle (5mm above skid plate compared to 5.5mm with standard gearbox)
- Simple design
Requirements:
- Small motor with 9mm hole spacing (M1.4) maximum 12mm diameter (like a 1224 or similar)
- Default 0.3 mod gears and bearings (I prefer to buy the gears and bearings separately but it's definitely OK to cannibalize a good quality gearbox such as from INJORA)
- 1x M2x14 countersink (upper screw to fixate gearbox shells) (Note: Mine are TOO LONG on the pictures and I had nothing else at that very moment)
- 2x M2x14 allen screw (lower screws to bolt on gearbox to skid plate)
- 3x M2 nylon nut (gearbox assembly and bold on gearbox to skid plate. I recommend to have the nuts all on the same NOT spurgear side....NOT bad as on the pictures)
- 2x M1.4x5 to bolt on the optinal gear cover
- 2xM1.4 washer or even better spring ring or lock washer (for the motor screws)
- 2x M1.4x6 to bold on the motor (motor screws)
Printing:
- I'd start with PETG and believe that'll do it, but let me know about any negative or positive experience
- Use any AI to ask for optimal SCX24 gearbox printing with your slicer and printer to get the best out of it
- Use properly dried and high quality filament
- Separate parts when importing to slicer and chose sufficient accuracy/precision, 100% infill etc.
- I've used a X-Y hole compensation of 0.05 when printing PETG
- Use sandpaper for the skid plates depending on your print quality so they can glide better over obstacles
Finishing:
- Organize all parts
- Assemble gears bearings and gearbox shells (be mind ful with the center bolts since they can break easely, check sufficient play first)
- Bold on the middle upper M2 to fixate gearbox shells and verify proper gear play
- Mount the motor to the mount and adjust gear play between spur gear and pinion gear (this is very simple since the spur gear is NOT fully covered yet). Make sure the motor does NOT rub on the mount when turning (it's tight but should have a small gap)
- Mount the gearbox to the decided skid plate
- Verify fully functionality and gear play
- Dismantle everything again, grease gearbox/gears/bearings and start over on step 2 :-)
Additional information:
- Have mercy on me since I’m not English native
- For this model I bought high-quality steel sealed bearing sets from AliExpress “Fimonda Official Store” and Axspeed 0.3M Steel Transmission Gear Gearbox Internal Gears which has NO spur gear unfortunately
- I’ll create and upload more similar designs playing around with the stock gears
- Any constructive feedback highly appreciated
Category: R/C Vehicles