SKÅDIS LEGO Star Wars Midiscale Display Holders

This is a growing collection of wall-mounted display holders for LEGO Star Wars midiscale models. Every holder is designed around the original LEGO display stand, so the model and its nameplate stay together while mounted on an IKEA SKÅDIS board.

The holders use two separate T-Clips from Xuis' Skadis T-Clip System. The shelves provide matching seats for these separate clips; the clips are not included in this model. Choose the T-Clip variant that matches your SKÅDIS board.

The surface outside each stand recess is LEGO-compatible. It uses an 8 mm stud pitch, 5.10 mm diameter studs, and 1.8 mm stud height. The 5 mm deep recess itself stays smooth, so the original display stand sits flat.

Included holders

Models

Acclamator-Class Assault Ship (75404)

• File: StarWars_Acclamator_75404.stl

• Shelf footprint: 160 × 127 mm

• Original stand centre: 83 mm from the SKÅDIS board

• Recess: 5 mm deep, open at the nameplate side, with a 15 mm wide rear relief for the round part of the base

• Surface: 156 LEGO-compatible studs outside the recess

Invisible Hand (75377)

• File: StarWars_InvisibleHand_75377.stl

• Shelf footprint: 160 × 115 mm

• Original stand centre: 71 mm from the SKÅDIS board

• Recess: 5 mm deep, open at the nameplate side, with a 15 mm wide rear relief for the round part of the base

• Surface: 116 LEGO-compatible studs outside the recess

Millennium Falcon (75375)

• File: StarWars_MillenniumFalcon_75375.stl

• Shelf footprint: 160 × 167 mm

• Original stand centre: 101.5 mm from the SKÅDIS board

• Recess: 5 mm deep, open at the nameplate side, shaped for the Falcon's own base

• Surface: 262 LEGO-compatible studs outside the recess

Tantive IV (75376)

• File: StarWars_TantiveIV_75376.stl

• Shelf footprint: 160 × 111 mm

• Original stand centre: 67 mm from the SKÅDIS board

• Recess: 5 mm deep, open at the nameplate side, with a 15 mm wide rear relief for the round part of the base

• Surface: 136 LEGO-compatible studs outside the recess

Kylo Ren's Command Shuttle (75406)

• File: StarWars_KyloRenCommandShuttle_75406.stl

• Shelf footprint: 160 × 119 mm

• Original stand centre: 75 mm from the SKÅDIS board

• Recess: 5 mm deep, open at the nameplate side, with a 15 mm wide rear relief for the round part of the base

• Surface: 156 LEGO-compatible studs outside the recess

AT-AT (75440)

• File: StarWars_ATAT_75440.stl

• Shelf footprint: 160 × 143 mm

• Original stand centre: 65 mm from the SKÅDIS board

• Recess: 5 mm deep, open at the nameplate side, with a deeper main area for the AT-AT's larger base

• Surface: 154 LEGO-compatible studs outside the recess

Venator-Class Attack Cruiser (75441)

• File: StarWars_Venator_75441.stl

• Shelf footprint: 160 × 135 mm

• Original stand centre: 91 mm from the SKÅDIS board

• Recess: 5 mm deep, open at the nameplate side, with a 15 mm wide rear relief for the round part of the base

• Surface: 196 LEGO-compatible studs outside the recess

Required hardware

• 2 × T-Clip from Xuis' Skadis T-Clip System for each holder, printed separately

• IKEA SKÅDIS board

• The relevant LEGO Star Wars midiscale model with its original display stand

Assembly

1. Print the shelf and two compatible T-Clips from Xuis' Skadis T-Clip System.

2. Insert the two T-Clips into the integrated upper Clip Seats.

3. Position the shelf on the SKÅDIS board and rotate both clips to lock them.

4. Place the original LEGO display stand in the recess, with the nameplate at the open side.

Recommended Print Settings

• Nozzle: 0.4 mm

• Layer height: 0.20 mm

• Perimeters/walls: 4

• Top and bottom layers: 5

• Infill: 15% gyroid

• Orientation: print flat, with the LEGO-compatible stud surface facing up

• Supports: none intended; inspect the slicer preview around the Clip Seat openings before printing

Use a material appropriate for the load and the installation environment. Check the fit of the T-Clips, recess, and SKÅDIS installation with your own print before placing a model.