DIY 100W USB-C Power Bank Case - 5x 18650 (5S1P), MYZL-YD24 board
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A compact two-part case for a 100 W DIY power bank built on the MYZL-YD24-V2.32 board and five 18650 cells in series.
- Ocena
- 0 / 5
- Polubienia
- 8
- Pobrania
- 26
- Wydruki
- 0
- Wyświetlenia
- 159
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
I built my own 100 W power bank around the popular MYZL-YD24-V2.32 board ("100W 5S Flash Charge Mobile Power Circuit Board") and designed this case for it.
The case is only 97 × 23 mm in footprint: five 18650 cells stand side by side in a single row, and the board sits under the lid, with openings for all four USB ports and the battery-level display.
Features
Fits the MYZL-YD24-V2.32 board: 2× USB-C (PD 3.1 / PPS, up to 100 W in and out), 2× USB-A (QC3.0 / SCP / AFC and more), digital percentage display
5× 18650 cells in 5S1P (tested with Samsung INR18650-25R)
Two parts, printed without supports
Two-colour look: black body, orange lid (any colours work)
STEP files included, so it's easy to remix for your own board or cell count
Bill of materials
1× MYZL-YD24-V2.32 power bank board
5× 18650 Li-ion cells, identical model and charge level (I used Samsung INR18650-25R, 2500 mAh, 20 A)
16 AWG wire for the main battery leads (the board needs ≥10 A on the battery side) + thin wire for the balance leads
Kapton tape, insulating paper rings for the cell ends, a thin foam pad between the cells and the board
No screws or glue: the lid is a press fit
Assembly
Place the five cells side by side and connect them in series (5S). I soldered the connections directly to the cells and insulated everything with Kapton tape and paper rings. Spot-welded nickel strip is the safer option if you have a welder — soldering heats the cells, so keep it fast and use a powerful iron.
Solder the main B+ / B− leads (16 AWG) and the balance leads to the board exactly as shown in the board's wiring diagram — the board will not start without the balance leads.
Put a thin foam pad on top of the cells, slide the pack into the case and place the board on top.
Press the lid on. The openings line up with the 4 USB ports and the board's button; the display shows through the window in the case.
Capacity
5S1P of 2500 mAh cells ≈ 18.5 V × 2.5 Ah ≈ 46 Wh (roughly 12 500 mAh at 3.7 V).
Safety
Li-ion cells store a lot of energy. Use only matched, healthy cells, never short them, and don't leave the power bank charging unattended until you have tested it. ABS is recommended over PLA: the cells and the board get warm at 100 W.
Print settings
Printer: QIDI Q1 Pro, nozzle 0.4 mm
Material: ABS (black case, orange lid)
Layer height: 0.14 mm (first layer 0.2 mm)
Walls: 3, top/bottom layers: 6
Infill: 20 % adaptive cubic
Supports: none, brim: none
Orientation: as in the files — case upright with the open side up, lid flat
Files
Case.stl, Lid.stl — ready to print, already oriented
Case.step, Lid.step — for remixing
Orca project (Qidi Q1 Pro).3mf — my OrcaSlicer project with the exact settings
Credits
The port and button cut-outs are based on 100W Power Bank 4S 18650 Double C Port by @Alexeyvik — thanks!
