1 / 9
Toyota GR Yaris Intake Duct / Air Scoop with Bottom Vent: Gen 1 and Gen 2 CFD Tested — zdjęcie 1
1 / 9

Toyota GR Yaris Intake Duct / Air Scoop with Bottom Vent: Gen 1 and Gen 2 CFD Tested

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Two-part GR Yaris intake duct upgrade with a bottom vent for lower temps and more induction noise. CFD-tested.

Ocena
0 / 5
Polubienia
4
Pobrania
20
Wydruki
0
Wyświetlenia
152
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution — Noncommercial

A two-part, 3D-printable intake duct for the Toyota GR Yaris (Gen 1 and Gen 2), remixed from the Hel'Scoop System. It keeps the original fit and mounting, and adds a bottom vent to supply more air to the lower duct on the intake housing. 

ABS or ASA will technically work; however, Nylon filament such as PA6-CF or PAHT-CF is highly recommended for its temperature resistance. 

How the vent works.

The vent works together with the factory airbox. Below 3,600 rpm, Toyota's intake valve keeps the airbox's second inlet closed for lower intake noise. Above 3,600 rpm the valve opens, and the vent feeds that inlet directly, supplying extra air to the lower duct on the intake housing when the engine needs it most. At full throttle, the fast-moving air in the duct lowers the pressure at the vent and draws a small amount of air back in from the lower pocket, balancing the flow between both inlets. Overall the duct adds some induction noise and is approximately 4 times less restrictive than the stock duct.

What changed from the original design.

  • Bottom vent: added to supply more air to the lower intake-housing duct. The factory airbox opens a vacuum-operated flap on this lower inlet under higher engine demand, and the vent keeps it fed. Three angled internal ledges guide the flow.

  • Lighter: about 8% less material than the original (12% with the Voronoi pattern), mostly from a slimmer airbox end.

  • Optional Voronoi pattern: outside surfaces only, recessed 0.6 mm. The inside of the duct, glue faces, mounting holes and the vent are left untouched, so airflow and fit are the same as the plain version.

Airflow testing (CFD)

Simulated in OpenFOAM (steady-state, k-omega SST) and compared with the factory duct shape. The figures show pressure loss through the duct; lower values mean less restriction.

Version

Full throttle, 100 km/h

Cruise

Factory duct shape

223 Pa

not tested

This duct

59 Pa

2.3 Pa

  • The factory duct was simulated without its foam insert and mesh, so its real-world restriction is likely higher.

  • At full throttle, the vent sends some airflow into the lower duct on the intake housing, keeping the factory airflow path.

These are simulation results, not dyno figures.

Real-world results

  • Intake temperatures: a few degrees lower than stock during spirited driving.

  • Sound: a little more induction noise than the factory duct, noticeable mainly under throttle.

Assembly

  1. Lightly scuff the glue surfaces with 240 grit and use a hobby knife to remove any high spots.

  2. Wipe with isopropyl alcohol and let dry.

  3. Bond with a slow-setting two-part epoxy such as Araldite Super Strength 8ml from Bunnings. Avoid superglue, which weakens over time on nylon.

  4. Clamp or tape in place and let it cure for 24 hours before fitting.

Fitment

Fits all Gen 1 and Gen 2 GR Yaris models.

Credit

Remixed from the Hel'Scoop System by ederh. Full credit to ederh for the original design this is based on.

Tagi