1 / 4
Mount for Ecowitt Sensor Radiation Shield — zdjęcie 1
1 / 4

Mount for Ecowitt Sensor Radiation Shield

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

For mounting the original sensor radiation shield on an exterior windowsill. Easily clip the sensor on and off.

Ocena
0 / 5
Polubienia
2
Pobrania
3
Wydruki
0
Wyświetlenia
32
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Sensormount for ecowitt Sensor Radiation Shield

Intended use

The original shield for the ecowitt WH57/WN32/WN31/WN30 is delivered with a mounting-arm that is of little use for mounting the sensor on a flat surface, e.g., on a windowsill. Furthermore the procedure to clip it on/off to the original baseplate is not very refined.

Thus this new baseplate replaces the original arm and baseplate with a design with these features:

  • Mounts to a flat surface either with two countersunk screws or doublesided tape

  • Allows angular compensation for upright positioning of the shield

  • Smooth and reliable locking mechanism via two buttons

The original shield itself is used as it is.

Remark: The uploaded files contain also a model of the bottom of the shield, but this was only used as a template/shapebinder for designing the new baseplate

Partslist

To buy

Part

Pieces

Ecowitt Sensor Radiation Shield / original part

1

Screw M3x30 ISO7380-1 (or similiar type)

2

Screw M3x35 ISO7380-1 (or similiar type)

1

Nut M3 DIN934

1

Spring 7x19mm (or similiar size)

2

Spring 5,5x38mm (or similiar size)

2

To print

Part

Pieces

EcoWitt_Top

1

EcoWitt_Bottom (choose one from two versions) 

1

Plunger

2

Spring_Lock

2

LockTab

2

Angle_Lockplate_Screwed

1

Lockplate_Nut_Screwed

1

Make

Printing hints

Original make used a Prusa Mk4S, PETG (Filatech Easy PETG, Extrudr PETG) and Prusa Slicer. Only a few parameters of the standard slicer-setup "0,2mm Structural" have been changed - please see the 3mf-files.

Remark: Due to my experience, the Prusament PETG-profile works better for the Extrudr PETG (not XPETG) than the dedicated Extrudr PETG-profile of the slicer - I use the Prusament-profile for Extrudr-PETG. For Filatech, the profile in the slicer works fine or me.

Assembly
  • insert the plungers, and short springs into the Top and lock them by turning the springlocks 90 degree with a slotted screwdriver

  • Insert the buttons "LockTab" with the long springs and secure them with the 30mm-screws

  • Press the M3-Nut into Lockplate_Nut_Screwed

  • Press the Lockplate_Nut_Screwed through the hex-hole in Angle_Lockplate_Screwed

  • Insert the lockplate-assembly through the bottom-hole into EcoWitt_Top and secure it with the 35mm-screw

Remark: The difference between the two versions of the EcoWitt_Bottom is just that one has no screwholes and is intended only for mounting with double sided tape. The more versatile variant is the one with the screwholes.

Finally

I would be glad if you find the design useful - have fun!

Tagi