1 / 4
Tulip Utensil Holder – Press-Fit Box with Fit Test — zdjęcie 1
1 / 4

Tulip Utensil Holder – Press-Fit Box with Fit Test

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Utensil holder with a see-through tulip. Five flat parts press-fit together, no glue or supports. Fit test included.

Ocena
0 / 5
Polubienia
0
Pobrania
2
Wydruki
0
Wyświetlenia
23
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Kitchen
Licencja
Creative Commons — Attribution — Noncommercial

ABOUT

A square holder for wooden spoons, spatulas and other kitchen utensils, with a tulip cut all the way through the front wall. It started as a laser-cut box (Boxes.py layout, 6 mm material) and was converted for FDM printing: the laser kerf compensation was removed, and printing clearances were added to every joint.

The box is five flat parts: four walls joined by finger joints at the corners, standing on a base with tabs that go through slots. Everything press-fits, so you don't need glue, screws or supports.

DIMENSIONS

• Assembled: 112 × 112 × 150 mm (base 112 × 112 mm, walls 100 mm wide)

• Inner space: about 88 × 88 mm

• Wall and base thickness: 6 mm

• Wall parts: 99.9 × 149.9 × 6 mm each, printed lying flat

PARTS LIST

• wall_A_tulip_v3 – front wall with the tulip cut-out

• wall_A_slots5_v3 – back wall with 5 slots

• wall_B_left_v3, wall_B_right_v3 – side walls with 4 slots each

• base_v3 – base plate with 12 slots for the wall tabs

• fit_test_v3 – small clearance test, print this first (see FIT TEST)

• assembly_preview_v3 – the whole box assembled, for viewing only, not for printing

FIT TEST

Every joint is designed with 0.08 mm of clearance per side. Whether that is snug or loose depends on your printer, filament and slicer, so the fit test lets you check it in a few grams of filament before you print about 220 g of walls.

The fit test is a plate with three slots and a separate key. The key's tab is identical to a real wall tab. The slots are marked with engraved dots:

• 1 dot – 0.06 mm per side (tighter)

• 2 dots – 0.08 mm per side (= the base and walls in this set)

• 3 dots – 0.10 mm per side (looser)

Push the key into each slot. You want the one that goes in with firm hand pressure and doesn't fall out when you turn the plate over.

• 2 dots fit best → print the parts as they are.

• 1 dot fits best (your printer prints loose) → tighten the walls by about +0.02 mm (see below).

• 3 dots fit best (your printer prints tight) → loosen the walls by about −0.02 mm.

For my own prints (Prusa CORE One, Prusament PLA), an earlier test showed 0.05 mm too tight, 0.10 mm slightly loose and 0.15 mm loose, so this set uses 0.08 mm.

CUSTOMISING THE FIT

The walls carry both mating surfaces: the corner finger joints and the tabs that go into the base. So you can tune the whole box in the slicer, without touching the model:

• PrusaSlicer: right-click each wall → Add settings → Advanced → XY Size Compensation. A negative value (e.g. −0.02) makes the tabs and fingers thinner, so the fit gets looser. A positive value makes it tighter.

• Other slicers have a similar per-object setting (for example, "X-Y contour compensation" in Orca/Bambu Studio).

• To check the value before printing all the walls, apply the same setting to the fit-test key and print the fit test again.

• Leave the base alone. A positive value on the base would make its slots smaller, which works against the change on the walls.

PRINT SETTINGS

Printer: Prusa CORE One, 0.4 mm nozzle

Material: Prusament PLA

Profile: 0.20mm STRUCTURAL

Layer height: 0.2 mm

Perimeters: 2, top/bottom layers: 5/4

Infill: 20 % grid

Supports: none

Brim: 5 mm (outer only)

Temperature: 225 °C (230 °C first layer), bed 60 °C

The 3MF has three print beds (PrusaSlicer 2.9 or newer):

• Bed 1 – base + fit test: ~1 h 42 m, about 49 g

• Bed 2 – both A walls: ~3 h 7 m, about 88 g

• Bed 3 – both B walls: ~2 h 56 m, about 84 g

Total: ~7 h 46 m, about 220 g

TIPS

• Print every part lying flat, as in the files.

• Two colours: print bed 2 (A walls) in one filament and beds 1 and 3 (B walls and base) in another. Mine are green and red. You only change the spool between beds, so you don't need an MMU.

• Keep elephant-foot compensation on (0.2 mm in the Prusa profile). Without it, the first layer of each tab flares out, and the joints get tight.

• Assembly: join the four walls at the corners first, then press the box down into the base until all the tabs are flush with the underside.

• If a corner is too tight, sand the faces of the fingers lightly instead of forcing them. The tulip wall is the most delicate part.

FILES

• STL – the five parts, the fit test and the assembly preview

• 3MF – PrusaSlicer project with the three beds and the settings above

• bgcode – ready-to-print files for the Prusa CORE One (0.4 mm nozzle, PLA), one per bed

• generate_holder_v3.py – the Python script that produced the STL files. Included for reference: it reads my laser-cut SVG layout, which isn't part of this upload, so it won't run on its own.

I generated the parts with a Python script written with AI assistance.

Tagi