1 / 6
Smart Coin Jar with Sound & RGB Lights (ESP32) — zdjęcie 1
1 / 6

Smart Coin Jar with Sound & RGB Lights (ESP32)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Coin jar that lights up and plays a sound when you drop a coin in.

Ocena
0 / 5
Polubienia
0
Pobrania
1
Wydruki
1
Wyświetlenia
21
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Gadgets
Licencja
Creative Commons — Public Domain

Smart Coin Jar – ESP32 piggy bank with sound & light

A compact 3D-printed coin bank with a "smart" lid. Every coin you drop in is detected by an infrared light barrier – the jar plays a short chime through two small speakers and lights up from the inside with addressable RGB LEDs. All electronics are hidden in the lid, powered by USB-C, and the firmware updates itself over Wi-Fi (OTA) from GitHub releases, so the lid never needs to be opened again.

WHAT IT DOES

  • Detects every inserted coin (IR LED + phototransistor break-beam in the coin slot)

  • Plays a chime on 2 speakers (I2S stereo amplifiers)

  • 5 RGB LEDs shine down into the jar and flash on every coin

  • Automatic over-the-air firmware updates from GitHub releases

  • Powered by a 5 V USB-C adapter; the cable exits downward along the jar neck

  • All coins fit through the slot

PRINTING

  • Printed in PETG

  • No supports needed – all overhangs are 45° or less

  • Lid: body, top cover and small holders (amplifier bar, USB-C holder, LED plate, sensor caps, ESP clamps)

  • Jar: see-through diamond lattice body (Ø90 mm), the neck fits the lid groove; openings are small enough that no coin can fall out

SOFTWARE

GitHub (PlatformIO, Arduino framework, ESP32)

HARDWARE

WIRING (ESP32-DevKitC 38pin, pins labelled as on the board)

  • Power

    • USB-C adapter: VBUS -> 5V rail, GND -> GND rail (D+/D- not used – power only)

    • 5V rail feeds: ESP32 "5V" pin, both amplifiers (Vin) and the LEDs (VDD)

    • GND is common for everything: ESP32, amplifiers, LEDs, IR LED, phototransistor

    • 470 µF electrolytic capacitor at the left amplifier between Vin (+) and GND (−) – buffers current peaks from audio and LEDs

    • Recommended power supply: 5 V / 3 A USB-C

  • Audio – 2× MAX98357 (I2S), wired in parallel

    • G26 -> BCLK (both amplifiers)

    • G25 -> LRC (both amplifiers)

    • G22 -> DIN (both amplifiers)

    • Vin -> 5V, GND -> GND (both amplifiers)

    • Channel select via the SD pin:

      • Left amplifier: SD wired directly to Vin

      • Right amplifier: 470 kΩ resistor between SD and Vin

    • GAIN left unconnected (9 dB)

    • Speaker wires soldered directly to the + / − pads of each amplifier (screw terminals and headers not used)

  • RGB LEDs – 5× WS2811 5 mm (pin 1 = DOUT on the flat side, pin 2 = VDD longest leg, pin 3 = GND, pin 4 = DIN)

    • G33 -> 330 Ω -> DIN of LED1

    • Daisy-chain: DOUT LED1 -> DIN LED2 -> ... -> DIN LED5 (DOUT of LED5 stays unconnected)

    • VDD of LED2–LED5 -> 5V, GND of all LEDs -> GND

    • VDD of LED1 is fed through 2× 1N5819 Schottky diodes in series from 5V (stripes towards the LED). This lowers LED1's supply to ~4.3 V, so the 3.3 V data signal from the ESP32 is read reliably. LED1 then regenerates a full 5 V signal for the rest of the chain.

    • 100 nF ceramic capacitor between VDD and GND directly at every LED

    • All LEDs mounted with the flat side facing towards LED5

  • Coin sensor – IR break-beam across the coin slot

    • IR LED (940 nm): G32 -> 100 Ω -> anode (longer leg), cathode (shorter leg) -> GND

    • Phototransistor 5800B (flat top):

    • collector (shorter leg) -> 3V3

    • emitter (longer leg) -> G34, plus 10 kΩ from G34 to GND

    • Optional: 100 nF between 3V3 and GND (not across the phototransistor legs)

    • Note: G34 is input-only on the ESP32 – it can read the sensor but cannot drive the IR LED

  • Optional

    • 10 µF capacitor between EN and GND – the board then enters upload mode automatically, without holding the BOOT button


Designed & built by Ing. TULák

GitHub: https://github.com/davidvancl

If you print it, please share a Make – I'd love to see your version! Questions, ideas or improvements are welcome in the comments or as an issue/PR on GitHub.

Thanks for downloading and happy saving! 🪙

Tagi