1 / 4
Tilt-Out Screwdriver Holder for 1/4" Pegboard – Expandable, No Hardware — zdjęcie 1
1 / 4

Tilt-Out Screwdriver Holder for 1/4" Pegboard – Expandable, No Hardware

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Each holder tips forward so drivers come out with no headroom. Add more holders to extend it. All printed, no hardware.

Ocena
0 / 5
Polubienia
24
Pobrania
9
Wydruki
0
Wyświetlenia
190
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Organizers
Licencja
Creative Commons — Attribution — Noncommercial

Tip it forward, pull the driver out

A screwdriver rack with holes holds drivers well, because they can't slide out the front. But to get a driver out, you have to lift it straight up until the tip clears the hole. So the board above the rack has to stay empty for the whole length of your longest driver.

In this rack, every holder tilts. Tip a holder toward you and the driver leans out, away from the board, so you pull it out at an angle instead of straight up. Nothing hung on the board above is in the way, so you can hang other tools just above the handles.

It's made entirely of printed parts: no bolts, no metal rod, no glue. To make it longer, print more holders.

How it works

  • Holders on cone pivots: each holder has a cone-shaped pin on one side and a matching cone socket on the other. The pin of each holder sits in the socket of the next one, so the row of holders is its own axle.

  • The end caps hold the row together: one end cap has a socket and the other has a pin. Both end caps screw to the pegboard, so the holders between them can't slide apart.

  • Built-in stop: the back of each holder has an angled face at the bottom. Tip a holder forward and it stops at 40°, when that face lies flat against the pegboard.

  • Each holder moves on its own: tip one forward and take the driver. When you put the driver back, push the holder upright again.

Make it as long as you need

Each holder adds 2" (50.8 mm), which is two pegboard holes, so the end caps always land on holes. Print one holder for each screwdriver.

  • 2 holders: 8" (203 mm) long, screws 6" (152 mm) apart

  • 4 holders, as in the photos: 12" (305 mm) long, screws 10" (254 mm) apart

  • 6 holders: 16" (406 mm) long, screws 14" (356 mm) apart

  • 8 holders: 20" (508 mm) long, screws 18" (457 mm) apart

For any number of holders, the rack is 2" per holder plus 4" long, and the screws go 2" per holder plus 2" apart.

What it holds

  • Shafts up to 1/2" (12.7 mm) across. The shaft goes all the way through the holder and sticks out the bottom, so long drivers fit.

  • Handles up to 1-1/4" (31.8 mm) across at the shaft end. The bottom of the handle sits in a counterbore 5/8" (15.9 mm) deep with a 5° taper, so the driver stands up straight.

The photos show it with Husky screwdrivers, including a stubby one.

How it hangs

It uses the same printed screw as my Magnetic Tool Holder Bar and Epoxy & Glue Bottle Holder. The screws go into the board first and the heads stay out. The rack hangs on them.

  • Grips the hole: the special 1/4"-20 thread is slightly oversize, so it bites into the edge of the pegboard hole and holds tight.

  • Self-centering: a tapered tip drops into the hole and centers the screw as you start it.

  • Flat-blade drive: the head has a slot for an ordinary flat-head screwdriver.

  • Locks the rack on: the underside of the head is a cone. The keyhole slots on the back of each end cap have tapered lips that fit that cone, so the rack can't pull away from the board.

Each end cap has two keyholes, one above the other, 2" (50.8 mm) apart. Confirm: one screw per end cap (2 in all, as on the plate), or both keyholes (4 screws)?

Pegboard compatibility

  • Standard pegboard with 1/4" (6.35 mm) holes on 1" (25.4 mm) spacing

  • The two screws go in one row. How far apart depends on how many holders you use (see the list above).

  • Tested on 3/16" (4.8 mm) thick pegboard

  • Not for IKEA Skådis or other slotted boards

Dimensions

  • End caps: 1.99" wide × 4.00" tall (50.5 × 101.6 mm)

  • Holders: 1.99" wide × 3.25" tall × 2.00" deep (50.5 × 82.6 × 50.8 mm), on 2.00" (50.8 mm) centers

  • Sticks out from the board: 2.31" (58.7 mm)

  • Pivot: 1.31" (33.3 mm) out from the board

  • Cone pins: 90° cones, 0.95" (24 mm) across at the base and 1/4" (6.4 mm) long

  • Tilt: 40° forward

The STEP files are included if you want a different hole or counterbore size for your drivers.

Print settings

I printed both end caps, one holder and two screws on one plate. On my Prusa CORE One it took 6 h 14 min and 221 g of PETG. Each extra holder adds about 1 h 42 min and 59 g (I sliced one holder on its own with the same profile to get that number). The 4-holder rack in the photos takes about 11 h 20 min and 400 g in all. My PrusaSlicer config file is included.

  • Printer: Prusa CORE One, 0.4 mm HF nozzle

  • Slicer profile: 0.25mm STRUCTURAL @COREONE HF0.4 (PrusaSlicer 2.9.6)

  • Material: Generic PETG, 250 °C nozzle, 85 °C bed

  • Layer height: 0.25 mm (0.2 mm first layer)

  • Perimeters: 2

  • Infill: 15% grid

  • Top / bottom solid layers: 4 / 3

  • Supports: snug supports under the rounded bottom edges only. I painted them with support enforcers and left automatic supports off. If you slice the STLs yourself, automatic supports with the default 40° threshold come out about the same.

  • Brim: none

  • Orientation: the holders stand upright with the counterbore on top, the end caps lie on their fronts with the keyholes facing up, and the screws stand on their heads

You'll need

  • A flat-head screwdriver to drive the printed screws

That's it. There are no bolts, no metal rod, no glue and no store-bought hardware.

Assembly and installing

Check that these steps match how you put yours up.

  1. Pick two pegboard holes in one row, as far apart as the list above says for your number of holders. For 4 holders, that's 10" (10 holes).

  2. Start a printed screw in each hole. The tapered tip centers it.

  3. Turn each screw in with a flat-head screwdriver until the underside of the head touches the board. Stop there, because plastic threads strip if you overtighten them.

  4. Line the parts up on the bench: the end cap with the socket, then the holders, with each pin in the socket of the one before it, then the end cap with the pin.

  5. Hold the row together, line up the keyholes in the end caps with the screw heads, push the rack flat against the board, and slide it down until it stops.

  6. Drop your screwdrivers into the holders.

To take the rack down, lift it up and pull it off the screws.

More pegboard holders with the same screws

Contest

Entered in the Printables Designer Challenge: Pegboard Wall Organizers.

If you print one, please post a Make and show how many holders you used.

Tagi