1 / 7
Mitsubishi MF355H Slim Laptop Floppy Case with Greaseweazle (Blue Pill) — zdjęcie 1
1 / 7

Mitsubishi MF355H Slim Laptop Floppy Case with Greaseweazle (Blue Pill)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Slim floppy enclosure for Mitsubishi MF355H with Greaseweazle (Blue Pill) inside – turns it into a USB floppy drive.

Ocena
0 / 5
Polubienia
0
Pobrania
1
Wydruki
0
Wyświetlenia
25
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
GNU General Public License v3.0

Two-part enclosure that turns Mitsubishi MF355H laptop floppy drive into a standalone USB floppy drive, with a Greaseweazle on an STM32 Blue Pill board inside.

Features
- Built-in front wall instead of the drive's bezel: disk slot with angled edges, LED window, eject button cutout and a finger notch with a gentle ramp for pushing the disk in. The front is split along the slot, so neither part needs bridges or supports.
- Four M2 screws go through the sides into the drive's own mounting holes and also hold the lid.
- The Blue Pill stands on its long edge in grooves in the floor and lid. There is 25 mm behind the drive for the flat cable and wiring.
- The USB cable exits at the back through a 3.5 mm hole split between the halves: you lay the cable in, no need to push the plug through. It is slightly clamped.
- Vent slots along the rear top edge.
Outer size: 103.7 × 161.6 × 25.4 mm.

Will it fit your drive?
Made for the bare MF355H (no bezel). Another slim drive should fit if it matches these:
- Frame: 95 mm wide, 14.4 mm tall at the front, 125 mm long; the rear connector does not stick out. Most slim drives are 12.7 mm tall – they will sit loose and the front won't line up.
- Side mounting holes: M2, two per side, 21.0 and 111.0 mm from the front edge of the frame, 2.75 mm above the bottom of the drive.
- Front, measured from the bottom of the drive and from the center as seen from the front:
- disk slot 7.0–11.8 mm up;
- eject button 26.75–38.75 mm right of center, 12.8–14.4 mm up;
- LED 23.75–28.75 mm left of center, 1.0–3.5 mm up.

You need
- Mitsubishi MF355H or another slim floppy drive with the same sizes (see "Will it fit your drive?")
- Greaseweazle on an STM32 Blue Pill (53 × 22.9 mm)
- 4 × M2×6 round-head screws, the usual laptop type (M2×5 minimum)
- USB cable about 3.5 mm thick

Printing
- Bottom prints as is. The lid is already flipped (ceiling on the bed).
- No supports.
- Printed in PETG, 30% infill. The gap between the halves is 0.15 mm.

Assembly
Before you start, bend the BOOT jumpers pins on the Blue Pill to the side so they lie flat, parallel to the board. This saves space inside the enclosure.
Drive onto the rails against the front wall → board into the bottom groove → USB cable into the notch at the back → lid on (the eject button goes through its cutout) → 4 screws.

Credits
Inspired by the [GW-Slim Case](https://www.thingiverse.com/thing:5327098) by [Bastich](https://www.thingiverse.com/Bastich/designs) (overall idea), the [Greaseweazle R1 Case](https://www.thingiverse.com/thing:6193592) by [krug3r](https://www.thingiverse.com/krug3r/designs) (board mount, USB cable exit) and the [Greaseweazle V4 Case](https://www.thingiverse.com/thing:5522437) by [astuermer](https://www.thingiverse.com/astuermer/designs) (vents). Designed from scratch in OpenSCAD – no geometry was copied.

How it was made
This model was designed together with AI – Claude Opus 5.5 by Anthropic. The ideas, measurements and design decisions are all mine; Claude turned them into OpenSCAD code and we went back and forth many times, refining and double-checking every detail along the way.
I exported the STL files myself, straight from that code in OpenSCAD – so there's no AI-generated mesh here, just plain, readable code turned into geometry. What you print is exactly what the code describes, nothing more.
And of course, it's been printed and tested in real life.

Tagi