1 / 3
DJI Osmo Pocket 4 Gimbal Clamp V2 – Improved Fit & Design — zdjęcie 1
1 / 3

DJI Osmo Pocket 4 Gimbal Clamp V2 – Improved Fit & Design

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Redesigned DJI Osmo Pocket 4 gimbal clamp with improved fit, refined tolerances, and a shape closer to the original.

Ocena
0 / 5
Polubienia
0
Pobrania
12
Wydruki
0
Wyświetlenia
61
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Photo & Video
Licencja
Creative Commons — Attribution — Share Alike

This is Version 2 of my DJI Osmo Pocket 4 gimbal clamp, redesigned to better match the original part and improve the fit compared to my first version.

I originally designed this clamp after losing the original one. Instead of buying a replacement, I decided to model and print my own. My first version was a simple, functional solution created entirely from scratch using manual measurements. It did the job, but I knew there was room for improvement.

For V2, I went back to the drawing board and modeled the part again, paying closer attention to the original clamp's shape and details. I also refined the geometry and tolerances to achieve a better fit than the first version.

I'm not a professional 3D modeler. CAD and 3D printing are hobbies I'm trying to improve at whenever I find the time. What might look like a relatively simple part to an experienced designer turned into a few days of measuring, modeling, adjusting, and learning for me. This version took roughly 3–4 days to complete.

That's what makes this project meaningful to me. Every model is an opportunity to learn something new, and revisiting an earlier design gives me a chance to apply what I've learned. V2 is not just an improved clamp; it's also a small step forward in my own modeling journey.

What's New in V2?

  • Closer to the original: The overall shape and details are more faithful to the original DJI clamp.

  • Improved fit and tolerances: The geometry has been refined to improve how the part fits compared to V1.

  • Remodeled from scratch: Rather than simply making minor adjustments to the previous file, I modeled the part again with the improvements in mind.

Purpose

The clamp is designed to keep the gimbal secured when the camera is powered off and reduce unwanted movement during transport and storage.

For additional protection, I recommend applying a soft protective layer, such as electrical tape, to the areas where the printed part contacts the camera. Check the fit carefully before use and never force the clamp into place.

Print Settings

  • Printer type: Standard FDM 3D printer

  • Material: PLA recommended; PETG is also an option

  • Layer height: 0.2 mm

  • Infill: 20–40%, depending on your preferred strength

  • Supports: A very small section may require support. The supported area is minimal, so even basic support settings should be sufficient.

  • Post-processing: Depending on your printer, filament, and settings, minor cleanup or light sanding may be necessary.

These settings are a starting point rather than a guarantee of identical results on every printer.

Important Notes

  • The model was test-printed on my own printer and worked as intended.

  • Fit and surface finish may vary depending on printer calibration, material, and print settings.

  • I cannot guarantee identical fit or results for every setup.

  • Check the fit and clearances before use.

  • Consiently designed ader adding a protective layer at camera contact points to reduce the risk of scratches.

  • This is an unofficial, independccessory. It is not affiliated with, endorsed by, or manufactured by DJI.

Feedback Is Welcome

If you decide to print this model, I'd love to see how it turns out. Likes, comments, and especially print photos are always appreciated.

I'm still learning CAD and 3D modeling, and feedback from people who actually print and use my designs would help me improve. If you notice anything that could be adjusted or have suggestions for a future revision, feel free to share them in the comments.

Thanks for checking out my model!

Tagi