1 / 9
HoldBar: clip-on hold keys for the Logitech MX Mechanical (one-handed shortcuts, no software) — zdjęcie 1
1 / 9

HoldBar: clip-on hold keys for the Logitech MX Mechanical (one-handed shortcuts, no software)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Slide a cap and Shift, Ctrl, Win or Alt stays held, so every shortcut takes one finger or a mouth stick. No screws.

Ocena
0 / 5
Polubienia
7
Pobrania
5
Wydruki
0
Wyświetlenia
148
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Ctrl+C with one finger.

Many shortcuts need two keys at once. If you type with one hand, a mouth stick or a head pointer, or your hand shakes or cannot stretch, that second key is the hard part. Software Sticky Keys helps, but it is set up separately on every computer, and the keyboard never shows you which key is "stuck".

HoldBar puts that on the keyboard itself. It is a small bar that clamps onto the front-left corner of the MX Mechanical, with one slider over each of Shift, Ctrl, Win (Option on a Mac) and Alt (Cmd). Push a slider's finger cap forward and it presses that key down and keeps it there. Now press the second key. Push the cap back and the key lets go.

Because it is purely mechanical it works on every device the MX switches between, with nothing to install.

Why I made it: I wanted shortcuts that don't need two hands. Multi-key shortcuts are hard for people who aren't dexterous or who have other difficulties using a keyboard, and I wanted something that helps with that.

Which files do I print? Have a multi-colour printer: print Plate 1, then HoldBar_Plate2_MULTICOLOUR_lid_sliders_caps (Windows or Mac). One colour: print Plate 1, Plate 2 and the TPU lettering. PETG is the main material and PLA also works (I printed and tested both). No brim needed.

Demo video (my own, of the printed piece): https://youtube.com/shorts/MYc97-Wp7n4


A note on the video: the knobs (finger caps) are hard to push with no keys under the piece. At the end of the video, with the demo key under it, the knob is much easier to push.

Who it helps

  • #OneHanded typists: Shift+letter, Ctrl+Z, Alt+Tab with the hand you have.

  • #MouthStick and head pointer users: one point of contact is enough for any shortcut.

  • #LowGrip, tremor or limited reach: the caps are 12 x 10 mm, big enough for a knuckle or the side of a hand, and a push of under 3 N moves them.

This is a design made with accessibility in mind. It is not a medical device, and I have not tested it with other users yet.

How to use it

  • Each cap sits next to its key name on the lid: SHIFT, CTRL, WIN (OPT on the Mac lid), ALT (CMD on the Mac lid).

  • A raised arrow on each cap points the way to push, so you can find it by touch.

  • Push the cap toward the dot: it clicks, the key is held, and the window in front of it shows the slider's colour.

  • Push it back to OFF: it clicks, the key releases, and the window goes dark.

  • Hold two at once for Ctrl+Shift shortcuts.

Features

  • No screws or magnets. The lid presses on over five printed pegs, and a little ordinary double-sided tape holds the clamp to the keyboard.

  • No tools to assemble: seven steps, all by hand.

  • Nothing slides on your keycaps. A small plunger stands on each key and only moves straight down, so the keycaps never get scuffed.

  • Off means off: when a slider is at OFF, only the plunger's own weight (about 0.1 grams) rests on the key.

  • Clicks into both ends, so a slider never drifts on or off by itself.

  • Clamps on and lifts off by hand. It never opens, drills or changes the keyboard.

  • Two lids, Windows (SHIFT, CTRL, WIN, ALT) and Mac (SHIFT, CTRL, OPT, CMD), so each name is as big as the lid allows.

  • One-colour printer (how I made mine): the lid, sliders and caps print in a bright colour. The key names, OFF marks and dots are cut into the lid. I printed them separately in black TPU and glued them in. A marker or paint pen works too.

  • Multi-colour printer: open HoldBar_Plate2_MULTICOLOUR_lid_sliders_caps (Windows or Mac). It has the lid with its lettering, the four sliders and the four caps with their arrows, with the lettering and arrows already on filament 2. Choose Load Whole File, and if the slicer shows one filament, add a second. No glue, no TPU, no brim. I don't have a multi-colour printer, so this version is untested on a real machine.

How it works

  • A slider pushes a small plunger down onto the key with a shallow 15 degree ramp. At the end of the ramp is a short flat, and there the key's own spring pushes straight up, so nothing pushes the slider back. It stays held with no latch to miss.

  • The plunger only moves straight down, so keycaps never get scuffed, and the plungers are T-shaped so they stay square in their slot.

  • The clamp hooks onto the keyboard's front-left corner and is sized from Logitech's official reference file (key positions, heights and the case edge).

  • Click stops at both ends, big caps with a raised arrow, and a coloured window that shows a held key. The lettering is cut into the lid so it works on a one-colour printer.

The numbers

These come from calculations, not measurements.

  • Held depth: 2.3 mm. The key fires at 1.3 mm and bottoms out at 3.2 mm. Over 81 combinations of parts printed 0.1 mm large or small it stays between 1.9 and 2.7 mm.

  • Push to hold: 2.9 N at most. To release: 1.8 N at most. It takes at least 0.6 N to move a parked slider, so a brushing hand will not change it.

  • The ramp (15 degrees) is shallower than the friction angle (about 17 degrees), so a slider left halfway stays where it is.

  • Hold-down: all four held keys pull the clamp up with about 2.4 N in total. The tape sits on the clamp's two vertical inner faces, about 8 square centimetres in all, so that pull is a sideways (shear) load, which tape resists far better than a peel. This is my estimate, not a test.

Print directions

Everything is set up so you can open a 3mf plate and slice it. Orientation is already in the plates. I printed on an Elegoo Centauri Carbon 2 (256 mm bed). On another printer, load the plate and re-arrange the parts. All plates: 0.4 mm nozzle, 0.2 mm layers, no brim, no supports (except the optional demo piece). Do not scale anything. The fits are built in.

Plate 1: bar, clamp and the four T-shaped plungers (PETG, dark colour)

About 1 h 46 min, about 25 g.

  • The bar lies flat. The clamp stands on its end (it is tall). The plungers lie on their side with the T profile flat on the bed, so the layers run along the stem.

  • What I used: 240 degrees C, 3 walls, 15% gyroid infill, textured PEI plate, slow outer walls on overhangs.

  • When it is done, drop a plunger into a well in the bar. It should drop in and slide up and down freely. If it sticks, a light rub with fine sandpaper on the stem fixes it. The plungers are printed 0.15 mm smaller per side than their holes.

Plate 2: lid, four sliders and four finger caps (PETG, bright colour; PLA also works)

I printed this plate in both PETG and PLA. The fits, the click stops and the sliders worked in both. The set in the video is PLA only because I had no bright PETG, and a bright colour shows up better against the black bar. Use the same settings as plate 1 for PETG.

PETG about 47 min, about 11 g. PLA about 43 min, about 11 g. (Slicer estimates.)

  • The lid prints top face down with its five pegs pointing up, so the top surface and the cut-in lettering come out smooth. The sliders stand on their tail end, which gives the ramp a smooth side. The finger caps print with the dish facing up.

  • PLA settings I used: 215 degrees C, bed 60 degrees C (65 for the first layer), part fan 100%, no brim. Keep the bed properly hot, because the small pieces need it to stay stuck down. Raise the bed temperature before you reach for a brim. For PETG use the same settings as plate 1.

  • Pick a colour that stands out against the black bar. That colour is what shows in the window when a key is held.

  • Check that each slider moves freely in the lid's track before you build it up.

Plate 3: black lettering and dots, then the OFF words (TPU 95A, one-colour printer only)

Plate 3 (Windows or Mac): the black lettering and dots, about 2 min 45 s. Plate 3b: the four OFF words, the same for both lids, about 2 min 20 s. Under 1 g each.

  • These lie flat. They are 0.5 mm thick, and the OFF words have strokes about 0.6 mm wide, so print slowly and peel them off gently.

  • Glue each piece into its recess in the lid with a drop of glue and tweezers. Use the lid's labels as a map: the words, the dots and the four OFF marks each have their own recess. A marker or paint pen works instead if you prefer.

  • Multi-colour printer? Skip this plate. The lettering and the arrows are already in the multi-colour Plate 2.

Optional: the keyboard demo piece (PETG, with supports)

About 2 h, about 18 g.

  • A corner of the keyboard's edge with one working key and its pin. It is tall (about 104 mm) and prints standing up, so turn supports on for it only. Use it to check the clamp and one hold before printing more.

Last: stick on the tape
  • Stick ordinary double-sided tape on the two flat inner faces of the clamp that face the keyboard (the front wall and the left side wall, the two legs of the L). Use thin tape and press firmly. Peel slowly when you take it off, and test a small spot first, since strong adhesive can leave a mark.

Quick reference
  • Plate 1: PETG. Bar, clamp, 4 plungers. About 1 h 46 min, about 25 g.

  • Plate 2: PETG (PLA also works). Lid (Windows or Mac), 4 sliders, 4 finger caps. About 47 min (PETG) or 43 min (PLA), about 11 g.

  • Plate 3: TPU 95A, one-colour printer only. Black lettering and dots (Windows or Mac), about 2 min 45 s, and the four OFF words, about 2 min 20 s.

  • Multi-colour printer: one plate, Plate 2 MULTICOLOUR (lid, sliders and caps), about 58 min, about 13 g including the wipe tower. Not tested on a real machine.

  • Optional: keyboard demo piece and its pin. PETG with supports. About 2 h, about 18 g.

What I could not test

I do not own a Logitech MX Mechanical, so I could not try HoldBar on a real keyboard. The key positions, cap heights and the keyboard's edge are measured from Logitech's official reference file, so the fit on a real unit is unverified. For the same reason I could not test the real key-pressing mechanism: how far the key goes down, the force it takes and how it feels come from calculations. I tested the slider, the ramp and the hold on a demo piece with a printed spring key, and the video shows it, but a printed key is not a real Kailh switch. The tape hold to keyboard is untested too. If you try it, please tell me what you find.

What's next

I couldn't find an existing add-on that holds modifier keys, so I made this one for the MX Mechanical. The same idea could be adapted to other keyboards. If it helps you, a like or a posted make means a lot, and ideas for other keyboards are welcome.

Assembly (by hand, no tools)

Step 1: Tape the clamp

Stick double-sided tape on the clamp's two flat inner faces (the front wall and the left side wall, the two legs of the L).

Step 2: Hook on the clamp

Hook the clamp under the keyboard's front-left corner and press it back onto the front edge.

Step 3: Slide in the bar

Slide the bar into the clamp's front channel from the right until it stops.

Step 4: Drop in the plungers

Drop a plunger into each well, stem first. All four are the same.

Step 5: Lay in the sliders

Lay each slider in its track at OFF, blade down.

Step 6: Press on the lid

Press the lid down over the slider tabs until it sits flat: a firm push over each of the five pegs.

Step 7: Press on the finger caps

Press a finger cap onto each slider's stem, sliders at OFF. A cap only fits one way round.

In real use

  • Copy and paste with one finger: push the Ctrl slider, tap C, then V, then push it back.

  • Select a range of files or text: push Shift, click the start, click the end.

  • Switch windows: push Alt, tap Tab as often as you need.

  • Gaming: hold Shift or Ctrl for sprint or crouch without holding it down.

Questions

  • Does it fit other keyboards? It is made for the Logitech MX Mechanical, sized from Logitech's official reference file. I have not tested it on other keyboards.

  • Will the tape harm the keyboard? The tape goes between the clamp and the keyboard's case edge, not on the keys. Strong adhesive can leave a mark, so use thin tape, test a small spot first, and peel it off slowly.

  • I only have a one-colour printer. Print the lid in one bright colour and add the black lettering as TPU pieces or with a marker. That is how mine was made.

  • Will it work with the Mac version? Use the Mac lid (OPT and CMD). Like everything here, it is untested on a real keyboard.

How the pictures were made

The second picture and the video are real photos and footage of my printed piece. The cover is my real photo placed onto a picture of the keyboard. The other pictures are Blender renders of the exact parts, made to look realistic with an AI image tool.

Files

  • Print-ready 3mf plates (Windows and Mac versions), an STL for every part, and STEP files.

  • The files are in folders: 1 Multicolour printer, 2 One colour printer (PETG), 3 One colour printer (PLA option), 4 Optional keyboard demo, 5 Single part STLs. Names say Windows or Mac. The STEP files are in two zips under Other Files.

  • Designed from Logitech's official MX Mechanical reference model. No part of that model is included.

Tagi