1 / 12
Temp Tower Compact — zdjęcie 1
1 / 12

Temp Tower Compact

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Compact temp tower: 9 mm modules with 35°/45° overhangs, overhang-limit tongue, 27 mm bridge, stringing and hole tests.

Ocena
0 / 5
Polubienia
5
Pobrania
48
Wydruki
0
Wyświetlenia
146
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Test Models
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

A compact temperature tower. Each 9 mm module is printed at its own temperature and tests overhangs, the overhang limit, bridging, stringing and small holes – one print shows how a filament behaves across its temperature range.

Size and print (7 modules): 64 × 20 × 64.2 mm · about 14 g, around 1.5 hours for PLA/PETG (ABS/ASA about 2 h, TPU about 2.5 h) – Prusa MINI+ with input shaper, 0.20mm SPEED profile.

What each module tests

  • 35° and 45° overhang wedges, each with a vertical Ø2.6 mm hole at the tip

  • Overhang tongue in the back pocket: its underside is a continuous arc that gets flatter towards the tip. Where it starts to droop shows the overhang limit at that temperature.

  • Target mark: a slot in the end wall at the nominal height of the tongue tip – if the tip lines up with the slot, it did not sag.

  • 0.5 mm ledge under the back pocket

  • 27 mm bridge with two stringing cones underneath

  • Horizontal Ø2.6 mm tunnel through the side wall

  • Hanging quarter disc in the 45° pocket, attached only to the inner wall

Labels: The temperature is engraved on the front of every module. The base plate shows 35°/45° under the wedges and the material on top; the underside carries material and temperature range, with room for a label strip (about 58 × 13 mm).

Material variants: PLA 220 → 190 °C, PETG 250 → 220 °C, ABS 260 → 230 °C, ASA 270 → 240 °C, TPU 240 → 210 °C – 7 modules each, 5 °C steps. Every variant comes as STL, as a PrusaSlicer project for the Prusa MINI+ with the temperature changes already set up, and as a ready-to-print G-code (Prusa MINI+ with input shaper, 0.20mm SPEED profile, default filament profile).

Printed and tested by me: PLA and PETG. ABS, ASA and TPU are sliced and checked, but I have not printed them – their temperature ranges follow the manufacturer recommendations (Prusa, Bambu Lab). Photos and feedback are very welcome.

Print Instructions

Settings

Setting

Value

Orientation

Standing on the base plate, as exported

Layer height

0.20 mm (tested, Prusa MINI+) and 0.12 mm (tested, Bambu Lab A1 mini – set the first layer to 0.12 mm as well). The temperature changes work with any layer height.

Supports

None – overhangs and the bridge are the tests

Brim

None

Perimeters / infill

Slicer defaults (e.g. 2 perimeters, 15 % gyroid)

Elephant foot compensation

Keep the slicer default

Seam

Not on the front face (temperatures)

Tested with

PLA, PETG

Your slicer will flag overhangs, a 27 mm bridge and sharp edges. They are intentional – rounding them would distort the result.

Temperature changes

The PrusaSlicer projects and G-codes already contain everything. If you slice the STL yourself, add one line of custom G-code. It sets the start temperature three layers before the first module and lowers it by 5 °C per module, right after the bridge of each module. The first two layers (base plate) print with the temperatures of your filament profile.

PrusaSlicer:

  1. Select the filament profile of your material. Do not change its temperatures.

  2. Printer Settings → Custom G-code → Before layer change G-code: paste the line for your variant at the end and keep the existing code (switch to Expert mode if the page is not shown).

  3. Save the printer preset under a new name so you can reuse it.

PLA 220 → 190 °C

{if layer_z > 0.5}M104 S{max(190, 220 - 5*int((layer_z - 0.5)/9.0))}{endif}

PETG 250 → 220 °C

{if layer_z > 0.5}M104 S{max(220, 250 - 5*int((layer_z - 0.5)/9.0))}{endif}

ABS 260 → 230 °C

{if layer_z > 0.5}M104 S{max(230, 260 - 5*int((layer_z - 0.5)/9.0))}{endif}

ASA 270 → 240 °C

{if layer_z > 0.5}M104 S{max(240, 270 - 5*int((layer_z - 0.5)/9.0))}{endif}

TPU 240 → 210 °C

{if layer_z > 0.5}M104 S{max(210, 240 - 5*int((layer_z - 0.5)/9.0))}{endif}

The line uses PrusaSlicer's macro syntax. Slicers derived from it (e.g. OrcaSlicer) use the same syntax, but I have not tested them. For other slicers such as Cura, change the temperature at these heights (e.g. with the ChangeAtZ post-processing script):

Module

above Z (mm)

PLA

PETG

ABS

ASA

TPU

1

0.5

220 °C

250 °C

260 °C

270 °C

240 °C

2

9.5

215 °C

245 °C

255 °C

265 °C

235 °C

3

18.5

210 °C

240 °C

250 °C

260 °C

230 °C

4

27.5

205 °C

235 °C

245 °C

255 °C

225 °C

5

36.5

200 °C

230 °C

240 °C

250 °C

220 °C

6

45.5

195 °C

225 °C

235 °C

245 °C

215 °C

7

54.5

190 °C

220 °C

230 °C

240 °C

210 °C

Model Origin

Inspired by Temp Tower PLA Prusa Mini+ by DerDave – the basic test layout (overhang wedges, bridge, stringing cones) follows the same idea. The model itself is a new parametric design, built from scratch in FreeCAD; no files were reused. The generator script was written with AI assistance.

License

CC BY-NC-SA 4.0 – share and remix with attribution, non-commercial only, under the same license.

The HogiBear name and the HB logo are not part of this license.

Design Highlights

  • A tongue instead of a staircase: The overhang tongue has a curved underside instead of steps, so the overhang angle changes continuously and you see exactly where the print gives up – not just which step failed.

  • A slot as a reference: The target mark sits in the end wall at the height where the tongue tip should be. Any sag is visible at a glance.

  • Sharp test edges on purpose: Wedges, bridge, ledge and pockets have no fillets or chamfers – they would hide what the test should show.

  • 9 mm modules on a 0.6 mm grid: Small enough to save filament and time. The main heights – base plate, module boundaries, ledge and bridge – line up with 0.10, 0.12, 0.15 and 0.20 mm layers. Tested at 0.20 and 0.12 mm.

  • Engraved, not embossed: All labels are shallow engravings in HogiBear Line, my own font for FDM printing, placed with clearance to the overhang slopes so the text does not disturb the test.

Need a different material or temperature range? Just ask. Module count (up to 12) and temperature range are parameters of the generator.


HogiBear – designed in FreeCAD, every file checked for printability.
Questions, ideas or photos of your print? Leave a comment – English or German, both welcome.
Viel Spaß beim Drucken!

Tagi