Liczymy pasujące modele…
A Temperature Tower designed to find the correct temperature for your filament! The included .gcode is sliced using Simplify3D with the "Multiple Processes" tool to set the temperatures at different layer heights. Take a look at the…
a bridging test that also includes a stringing test and an angle test all in one
Do you have a TV set close by your 3D printer like I have? If so, you most likely wanted to have a good way to store your TV control and your Switch2Pro controller close to the printer? Well - if you happen to have either… a Samsung TV…
10mm x 10mm x 10mm Calibration Cube including bridges from 1mm to 8.4mm and overhangs from 10deg to 70deg. Designed in OnShape. Should also help you calibrate your flow settings as the walls are mostly 0.8mm and then 0.4mm at the top.…
20mm x 20mm x 20mm Calibration Cube including bridges from 1mm to 16.8mm and overhangs from 10deg to 70deg. Designed in OnShape. Should also help you calibrate your flow settings as well with a 0.4mm thick section at the top of the x…
I wanted to have nice connectors for the extension of my MK3's PSU cables without having to tear down the entire cable harness. Since there were no proper screwing terminal blocks available out there, I did it maker style and designed my…
A hinge designed to test the bridging performance of your 3D printer. Hopefully it works better than your hinge profile... This is a print‑in‑place design. Have fun testing and printing :)
You may want to rotate the print 45 degrees on your build plate so that the part cooling is not biased I recommend using 125% bridging flow, and disabling thick bridges disable slow down for overhangs in global settings turn on forced…
Bed - Overhang - Bridging - Top layer Test for delta printers, but can be used for all kind of printers.
I use this test for years because it fast to print and easy to use, you can easely understand what to do to solve your problem whit stringing and bridge failure. If you don't want to test bridge you can make a cut at 22mm height and…
All in One Temperature & Bridging Tower - PLA MK4S GCode. Specifically sliced for the latest MK4S version with the 0.4mm high flow nozzle (HF0.4) Uses the default PrusaSlicer 0.2mm STRUCTURAL preset as that is what you will most likely be…
Temperature towers should be fast and easy. I don't want to wait for hours just for a test. This tower is shorter and narrower than most models out there and uses increments of 10C to quickly get you close to the optimal temperature for…
Designed to be printed at 0.3m layer and only takes about 11 minutes. if you scale it .6666666666 in the Z then it might work for a .2mm layer height but idk :-) . Please feel free to post results with the printer type as well as any…
Print intstructions: Print Bridge first. Print Body and pause in slicer before the first bridging layer starts. (be careful not to pause 1 layer too deep) Place Bridge inside (be careful not to detach the body from the print bed) Resume…
See description over here: https://www.printables.com/model/39810-improved-all-in-one-temperature-and-bridging-tower This is a remix for Prusa MK4S with and without MMU3. 17th December - Add MMU3 PETG and PLA 23th November - Fix for…
a bridging test that also includes a stringing test and an angle test all in one
Simple test print to print bridges from 1cm to 11cm in 1cm increments. On my Prusa Mk4S, the last few are imperfect but usable. (See photo). OpenSCAD file included to make your own versions.
Test the bridging on your 3D printer with this DNA Double Helix model! The long bridges are in alternate directions so you can check your cooling in every direction. I used the original version of this model to test my Positron , and I…
See description over here: https://www.printables.com/model/39810-improved-all-in-one-temperature-and-bridging-tower This is a remix for Prusa Core One / Core One + / Core One L. 05.06.25 : Added MMU3 profile. 28.12.25 : Added optimized…
This cute little calibration cube-variant can be printed in ~20 minutes and provides a bed adhesion, bridging, and dimensional accuracy test. Plus, they stack and make for great filament swatches! Each side of the main cube is 20mm. The…
Here is a bridging test from 10 to 100mm, it requires only 13g of filament. You'll have to flip it in your slicer because when you put it i't in vertical. I suggest to use the experimental bridge mode, which you can find at the end of the…
Print it without supports to tune-up temp vs print speed vs fan speed ratio vs filament brand for best results.
A simple test for testing bridging and stringing which I made in Tinkercad. Enjoy! UPDATE- I uploaded a new file : Bridging & Stringing Test V2 This file is an updated version of the previous one. I changed it so that it will take less…
I've seen a few ideas like this floating around but they either require assembly, bridging, and/or support. I'm also, not a fan of unnecessary vertical curves. I printed in PLA, 4 walls, and 20% cubic. The color change is just me getting…
My dughter just got her AOL, so I made this! It's blank, so if you need help adding the names, DM me and I'll teach you! SJT scouts scout boyscouts arrow arrowoflight
I always care to design thinking the best way to possibly omit the need of support in printing, so I got use to elaborate in mind also the slicing before to even run the slicer program. I draw this basket type of box initially even with a…
Hi:), I just made this model called a bridging test. The amount your printer would have to bridge is written on the top. You can choose what distance you want to bridge. Feel free to tweak around with the settings. I would appreciate if…
Do you have a TV set close by your 3D printer like I have? If so, you most likely wanted to have a good way to store your TV control and your Switch2Pro controller close to the printer? Well - if you happen to have either… a Samsung TV…
This tower allows you to test different temperatures in your printer! You can test 30º and 45º angles, bridging and curvature. You can use the PETG designed tower to test PETG, or the blank one to test any material. Printing a temperature…
I had problems with the fan shroud, so I needed a directional overhang / curling test. It will test overhang at four angles (30 to 60°) in all directions for curling issues bridging at 30, 50 and 70mm arcs at 2.5, 5 and 7.5mm radius (5,…
Wanted a smaller temp tower to just fine tune Prusaments +- 10c of recommended temperature. These are PLA and PETG models. Also sliced with PrusaSlicer. 3mf model files includes custom g-code for different temperatures so you just need to…
Features: - Uses little material because it is not too big - Different overhangs, 45° and a curved one - A thin wall at the overhang to test the layer adhesion by breaking it - A bridge, from 30mm length in the back to 35mm in the front -…
Efficient storage begins with small details. The Disk serves as an airflow distributor inside any standard vacuum storage bag — allowing air to be extracted evenly and the bag to compress smoothly without damaging the contents. Simply…
See the original for the right assembly model for the right assembly order. Screws that I used: d4x50mm chipboardscrews for the middle vertical connections (2x per block) d4x30mm chipboardscrews for the countersunk connections (8x per…
I present a simple and extremely fast-to-print model that serves as the ideal tool for calibrating and optimizing support settings and bridging in your slicer. This small cuboid provides comprehensive feedback in just a few minutes,…
This is My Print in Place 3D Printer Keychain! This is a cool gift for 3d printing enthusiasts and non-3d printing enthusiasts alike! It makes a great keychain for any maker, and makes it a lot harder to lose your keys! Print instructions…
This is My Print in Place 3D Printer Keychain! This is a cool gift for 3d printing enthusiasts and non-3d printing enthusiasts alike! It makes a great keychain for any maker, and makes it a lot harder to lose your keys! Print instructions…
With this model you can test 6 different distances: 10mm 20mm 40mm 60mm 80mm 100mm Update 1: Added a Material Saving Variant (But this Variant is more fragile)
I designed these mounts to manage the cabling under my desk using Velcro. Unlike most 3D printed velcro cable organizers these do no require any bridging when printed "Upside-down". They should be oriented correctly for this in the model…
This design adds supports to the corners and edges too, to improve reliability
Since I could not find the ideal temp tower that meets my expectations, I designed my own. Features: - Uses little material because it is not too big - Different overhangs, 45° and a curved one - A thin wall at the overhang to test the…
10mm x 10mm x 10mm Calibration Cube including bridges from 1mm to 8.4mm and overhangs from 10deg to 70deg. Designed in OnShape. Should also help you calibrate your flow settings as the walls are mostly 0.8mm and then 0.4mm at the top.…
20mm x 20mm x 20mm Calibration Cube including bridges from 1mm to 16.8mm and overhangs from 10deg to 70deg. Designed in OnShape. Should also help you calibrate your flow settings as well with a 0.4mm thick section at the top of the x…
Recommended Print Settings Rafts: No Supports: No Resolution: 0.2 Infill: 25 Notes: Nozzle temp: 200 Bed temp: 60 Print speed: 60mm/s
Test your bridging/cooling settings! Check if your bed adhesion is good enough for small footprint parts. Prints in minutes and uses less than 1 gram of filament. Category: 3D Printing Tests
This is a completely parametric temperature tower remake from Tronnic's work (rather than a remix). I liked its basic design, but I missed the ability to tweak on parameters, and hence it is! You can: Set the temperature range and the…
I've made these small temperature tower models so they can be printed relatively quickly in about 30 mins. Each model has 9 levels in 5 °C increments and a range of 40 °C. They range from 190-230 °C (suitable for most PLA filaments) to…
Ultra long, didn't even measure. Measured it as LONG. Put your speed low and cooling high, and use PLA. Much better cooling. Turn it downwards, as I accidentally knocked it over (lol). Megalong is even longer, don't know if it's even…
I wanted to have nice connectors for the extension of my MK3's PSU cables without having to tear down the entire cable harness. Since there were no proper screwing terminal blocks available out there, I did it maker style and designed my…
Hole Bridging Workaround Sometimes you have to orient a model so you end up with holes running parallel to the print bed and this can result in your nice round holes not being so round at the top due to bridging. To remedy this, I cut out…
This all-in-one 3D printer calibration test is designed to evaluate and improve your FDM printer performance quickly and accurately. The model includes advanced tests for bridging, overhangs, dimensional accuracy, tolerances, bed…
Just a quick printer test I made. I was tired of the majority of tests taking up to an hour to print. This design only takes 15-20 minutes on my CR-10S.
A simple bridging test, just like the title says :) This test goes from 10 mm to 100 mm, each block wall increasing by 10 mm This model can be printed upright (like the photo) or on its side and it shouldn’t change the results (besides…
Purpose of the Model Parametric temp tower for temperature tests, stringing, and bridging. Similar to models by Extrutim and the fixed version of FlorinB . Rebuilt from scratch in FreeCAD 1.1.1. Requirements To create your specific temp…
Support free version of A1 Mini purge bucket
Customized version of https://www.thingiverse.com/thing:476845 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=476845 Instructions Using the following options: min_bridge_length = 1 max_bridge_length = 10…
Brio compatible bridge set for Lego Duplo compatible pillars Description The provided STLs are for a 150mm straight rail in between and 2 Duplo brick pillars to reach Brios standard bridge height of about 60mm. Feel free to download the…
Brio compatible bridge set for Lego Duplo compatible pillars Description The provided STLs are for a 150mm straight rail in between and 2 Duplo brick pillars to reach Brios standard bridge height of about 60mm. Feel free to download the…
Just wanted a simple bridging test to tweak my settings and not waste a lot of filament. Category: 3D Printing
Temperature Tower to find the correct temperature for your filament Print instruction Material: PLA Print resolution: 0,20 Bed 60°C First 10mm prints with 190°C then every 5mm the temperature increases by 5°C !warning! Watch the first few…
Longer bridging test pieces to test out the limits of your machine. Dialing in just the right bridging settings can reduce the need for support structures in 3D prints and thus reduce print time and material use. Keep in mind that the…
Simpel bridging gap test from 1mm to 28mm to test your printers bridging proformance
Short Introduction VIDEO for the unofficial Drag Race. Are you needed to work on your bridging settings? Are you sick of using the same small feature of a model to print? This is a test you need! Three tests in all for .4 .6 and .8…
These objects test your printer's ability to bridge long distances. The two provided objects test bridging over 150mm and 200mm gaps. If you can bridge the 200mm gap, you're doing well. The above photos are ABS, printed with a .4mm…
Another in my series for makers to earn achievements for their dedication to 3D printing. Model prints with no supports and with 10% infill. Optional panels are included if you want to print brown/wood covers for the model base. This…
A simple test for bringing and stringing performance. It is very fast and costless in terms of filament. About 4g of filament and 15-20m test, you can obviously scale it in the slicer if you wanna. I needed a fast test for a fast tweaking…
Update: v1.9.6 10-10-25: Test cutouts on the backside are back! Somewhere around v1.8 I left a “*” character in the code while debugging that made them disappear. My “Improved All-In-One Temperature and Bridging Tower” is very popular but…
There are so many bridging test models out there already - why did I make another one? I couldn't find one that met all these criteria: The model should test bridging in both X and Y directions, testing each axis with the same range of…
Reinventing the wheel, yet again. The whole thing is 3 mm deep (z) and each strut is 1 mm wide and 0.8mm deep (so about four passes). The smaller one goes from 5mm to 50mm in 5mm interval; the bigger one goes to 75mm. Having trouble with…
This Nozzle brush is has the head flipped so there is no need for any support or bridging. I also shortened it to 13.5cm so it fit in the Ender 3 storage drawers. It's a remix of a remix since most of the work was already done. I Just…
This allows you to fine tune your bridging settings and to see what your limit is.
Print the central and upper shelves first, then the main part with pause points at 34.5mm and 37.5mm (pause just before the shelf begins printing). As it reaches these points, insert the shelves into the ledges. The printer will then…
Death by Bridging remixed, with last two steps removed (175mm & 200mm) to make it fit the Prusa Mini's printbed. I was hoping to fit 175mm as well, but couldn't make it, maybe someone else will have more luck with that.
This is basically an inverted standard calibration cube, and prints in about the same amount of time. But this one is hollow to test retraction, overhang angles, and an insanely difficult bridge at the top. The cube measures 20x20x20mm…
Warning! Make sure your printer can handle long bridges before printing! This is a three shelf model measuring 250 mm wide 150mm front to back and 100mm tall. I would suggest printing with a brim. Other than that no supports are needed,…
Just a quick test (about 1 hour) for testing the bridging capability of your FDM printer and its settings. Features: -bridge length: from 2cm to 10cm -bridge thickness: 2mm -thin base for better bed adhesion Advance: -you can play around…
Created this small cube that should be 20x20x20mm to test stringing + bridging capacity. Quick and use little materials. It also pairs as a fun optical illusion.
Prints inverted with 144 bridges that grow as it goes up. You may want to dial back speed at higher tiers. Very rigid.
Limo buggy, based on E3D's buggy benchmark, designed to test your printer's bridging ability over a very long distance. A little over 100 mm! Take your printer settings to the limit with this challenge! If you succeed, you can brag about…
This is a double helix bridging torture test. you can scale it up or down to increase the length of the bridge. you can also filament swap to test bridging capabilities of multiple filaments in one print! designed in fusion 360 featured a…
USE BRIMS - SLOW DOWN AS YOU GO HIGHER - MAY POP OFF PRINT BED Based on earlier learning with Air Trees https://www.printables.com/model/340401-air-trees-easy I wanted to see what was possible at the upper end of the technique. Recently I…
This is something I whipped up in Inventor Fusion this morning, and I like it. The 2 smaller versions are likely the only ones that are possible, so if you try the huge one and it fails, that's your fault :P I'd try to make the large one…
Added sacrificial bridging to make the unsupported pattern near the top easier to print without supports. Just need post-processing to trim away the four bits of bridging.
Just press print and you will see whether your printer is good at bridging or not. No supports (obviously).
90 Degree Overhang and Bridging Test Model for Arc Overhangs
Remixed the wonderful 10 Minute Mini Calibration Test for Oozing/Retraction at Different Distances by MrTestOne to also add bridging on the last layers. This probably takes more than 10 minutes now to build, but may be useful for some.
