Unfolded iPhone Duo Stand – Holds Only the Corners, Landscape + Portrait, Cable Window
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Cradle for the fully open iPhone Duo: only the two lower corners rest on the seat - edges, hinge and camera stay free.
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 48
- Wydruki
- 0
- Wyświetlenia
- 365
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Portable Devices
- Licencja
- Creative Commons — Attribution — Noncommercial
A one-piece stand for the fully unfolded iPhone Duo (open 164.6 x 117.8 x 5.2 mm, 254 g - Apple's spec page). The open phone leans back 20° and rests only on its two lower corners, which sit on a concave arc (R 150 mm). The seat floor is heeled - it falls 30° toward the back - so the phone's own weight keeps its bottom edge in the corner: the pose is held by the shape, not by friction (calculated). The same seat takes landscape (video) and portrait (recipes, calls), bare or in a case up to about 2 mm per side. No straight edge, no hinge and no camera is touched, and the middle is an open window: a charging cable can drop straight through to the table and leave at the back.
Validation status (please read): checked in CAD (12 seat cases for both orientations, corner radii 5-12 mm, bare and cased; edge clearances; calculated statics) and in the slicer. It has not been physically printed or tested - the phone ships on 23 October 2026, so no owner feedback exists yet; please report. Images are renders of the CAD model and drawings from it, not photographs; the phone in the images is a generic stand-in.
Features
Held only by its two corners: every straight edge, the hinge and the camera stay free - the stand stays at least 5.3 mm away from the straight edges beyond 8 mm from each corner (measured on the CAD).
A seat that holds by its shape (calculated for every case): the heeled floor holds the 20° lean with no friction at all (30° heel, at most 24° needed), and the phone's centre of mass sits 55-72 mm below the arc's centre, so it cannot slide off sideways. It does not level itself - set it level by eye and it stays where you set it.
One seat for both orientations, bare or cased - no measuring, no sizing.
Open window 94 mm wide under the phone: a charging cable drops through and leaves through an arch at the back.
One part, printed upright, no supports, no hardware.
Where it touches
Apple publishes no position for the USB-C port, buttons, speakers or cameras. The cradle avoids them by touching only the two lower corners and the lowest 40 mm of the back in landscape (never the middle 25 mm over the hinge line), or the lowest 51 mm in portrait (at least 31 mm below the hinge line). Nothing touches the screen in the seated pose. Look at your phone's back before you print.
Dimensions
172 x 115 mm footprint, 68 mm tall - fits beds from 180 x 180 mm (the project is set up on a 220 mm bed; on a 180 mm bed press Arrange). Seat: R150 arc, 20° lean, 13 mm groove (5.2 mm bare to 9.2 mm with a 2 mm-per-side case), floor heeled 30°. In landscape the phone's bottom edge sits 34-39 mm (along the screen) above the table.
Print settings
Matte PLA or PETG (switch the filament profile for PETG); any colour.
0.4 mm nozzle, 0.2 mm layers, no supports. Upright on its base, as it stands on the desk; 10 % infill is enough - the cradle is mostly walls.
openbook_complete_cradle.3mf: about 6 h 7 min and 83 g (PrusaSlicer 2.9.6 estimate on a generic PLA profile).
How to use it
Open the phone fully and lower it into the cradle with its back flat against the two lobes until both lower corners sit on the floor - landscape for video (camera edge up), portrait for recipes and calls (camera half up).
If the bottom edge ends up forward in the groove, the phone rests more reclined (up to about 34°, calculated): push the bottom edge back into the corner.
Set it level by eye. Lift it straight up to take it out.
To charge, drop the cable through the open window under the phone and out through the arch at the back (portrait with the port at the bottom: use an L-shaped plug).
Files
openbook_complete_cradle.3mf - ready-to-print PrusaSlicer project.
cradle.stl and model.py - the parametric CadQuery source: lean, arc radius, groove, window, lobes, tail.
Limitations
Not physically printed or tested; fit, clearance and stability are calculations on the CAD.
Not a typing stand: calculated, a push of about 1.8 N (landscape) / 1.3 N (portrait) at the top edge tips it backwards, and a press near the top (about 1-2 N, less on a slick phone) can push the bottom edge forward into a more reclined rest - push it back.
Cases thicker than about 2 mm per side were not checked. Made for the iPhone Duo only.
iPhone is a trademark of Apple Inc. This design is not affiliated with or endorsed by Apple. Images are renders of the CAD model and drawings from it, not photographs; the phone in the images is a generic stand-in.