Field PTT Switch Grip for 16 mm Push Button, Twist-Lock Cap
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Ergonomic grip for a push button with a twist-lock cap, for handheld PTT in POTA and SOTA field use.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 3
- Wydruki
- 0
- Wyświetlenia
- 21
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Overview
A handheld grip for a standard 16 mm panel-mount push button, built as a push-to-talk switch for field radio use. It has a gun-grip profile with three finger grooves and a thumb face tilted 15 degrees. The cap locks with a twist and a click detent, so it goes together without screws. A nut tool is included for tightening the switch from inside the cap. All three parts print without supports.
On the Air
I wanted a PTT I could hold easily during portable operating, that would pack into a go-kit bag and not rattle apart. A plain tube gets tiring, and screw-together housings loosen in the bag. This grip fits the hand, works with gloves, and comes apart in the field by twisting off the cap. Mine ends in a 3.5 mm mono plug, so it works with any of my radios that take a 3.5 mm PTT input. Wire it for whatever your rig needs.
Print Settings
- Nozzle: 0.4 mm
- Material: PETG. It holds up better than PLA in a hot car or in sun, and gives the crush ribs and detent a bit of flex.
- Supports: none
- Orientation (the STLs are already oriented this way):
- Grip: upright, standing on its base
- Cap: upside down, on its flat top face
- Nut tool: upright, standing on its handle
The twist-lock fit depends on your printer. Print the grip and cap on the same printer with the same material and settings. If the joint is too loose or too tight, adjust it in the .scad file (see Design Notes).
Hardware and Assembly
- 1x 16 mm panel-mount momentary push button (M12 x 1 thread, 14 mm hex nut, 14.3 mm bezel, about 20 mm of body behind the panel) - https://a.co/d/0fkTwauF
- Cable, about 5 mm OD, cut to the length you need - https://a.co/d/0euhhLuc
- 1x 3.5 mm mono plug (or the connector your radio needs)
- Heat-shrink tubing
1. Push the switch through the cap from the top.
2. From inside the cap, thread on the 14 mm nut and tighten it with the nut tool. The slit down the side of the tool lets it slip over wires that are already soldered.
3. Feed the cable up through the base of the grip and solder it to the switch terminals.
4. Tie a knot in the cable inside the grip so it can't pull out.
5. Line the cap up about 40 degrees counterclockwise from its final position, push it in, and twist clockwise until it clicks.
If the switch is too tight to slide into the cap, use a deburring tool to shave off a bit of plastic - I intended for the fit to be very tight. The first assembly will feel firmer than later ones while the crush ribs bed in. That is normal. To take it apart, twist the cap counterclockwise past the detent and lift it off.
Design Notes
- Twist-lock instead of screws or threads. A sloped channel pulls the cap down tight as it turns, and a detent holds it locked. It assembles in the field with no tools and does not loosen in a bag.
- Crush ribs on the cap plug. Small ribs shave down on first assembly to take up printer-to-printer variation, so the cap doesn't rattle.
- 15 degree top tilt. This puts the button where your thumb lands naturally when you hold the grip.
- Slit nut tool. A closed hex driver can't go over wires once they're soldered. The slit fixes that.
- Flared cable exit. The cable leaves through the base so nothing sticks out to snag.
The included .scad file can be adjusted in OpenSCAD's Customizer: grip height, width, depth and lean; number and depth of finger grooves; top tilt; joint fit (radial clearance, crush rib interference, lock squeeze, detent strength); cable diameter; maker's mark; and the nut size and slit width on the tool. Use the fit_test layout to print a short grip ring and a cap so you can tune the joint without printing the whole grip.
If you print one, I'd like to see your make and hear how the fit came out on your printer, or what switch and radio you paired it with. Remixes welcome.