1 / 10
The Print in Place Retractable Witches Broomstick! — zdjęcie 1
1 / 10

The Print in Place Retractable Witches Broomstick!

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

THE print in place fully retractable witches broomstick! The Spooky Halloween prop you didn't know you needed until now!

Ocena
0 / 5
Polubienia
4
Pobrania
1
Wydruki
0
Wyświetlenia
19
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Ladies and Gentlemen, Boys, Girls and possibly a cyborg.

This is the ONE and ONLY Print in Place Extending Witches Broomstick!  (i think?)

Extends to 72CM when printed at 255mm height!

Here is my rendition of a version of a remix of an un-remixable model! This is my first 3D Model made by myself caused by after printing an earlier version finding out that the original models weren't even remixable! 

Starting my own version with a different idea in mind a Corrupted version, I struggled in blender to create any type of mesh and after hours I had nearly fully given up, until i found SculptGL! Where after a few hours i had a close enough shape to what I was going for and a couple of hours later the model was ready for a handle inserting. For the Handle I used Autodesk Fusion which is really growing on me, I also went back and forth between them all along with Anycubic and Orcaslicer for repairing, scaling and cloning . After completing this first own version I wasn't quite happy, the handle worked well but was very angled and didn't extend to it fullest capabilities. But it was progress!! 

I then slept!

Version 2- The one you're printing

While having a coffee in the morning I took a second to think about my design. Coming up with the great idea of just creating a single small brush piece and clone it many time to create the brush like head. 10 minutes later was back on SculptGL, 2 hours later i had my shape. I then went back to my handle giving them all a lesser angle along with different end diameters. I then took some tori? to insert into BumpMesh (Thanks CNC Kitchen) giving them this nice knitted texture! Then to Anycubic slicer for a mass clone of my bristles I then arranged them on the plate, assembled and back into Fusion to add some middle mass, then cut out the tapered cylinder from the body so i could insert the new improved handle. After a few more slicer edits I was printing! <<< This only took 7 hours I had become a 3d modelling machine!

Printing....

Took it off the print bed and the handle slid right out! Successs!!!!!!!!!!!!!  All my upgrades have worked, the handle is  longer and are less angled along with being a completely different looking broom not just some corrupted mess (even though i was going for a corrupted look on the firs one) It did turn out more like an olde Stick Torch I've uploaded a pic. 

I have  set up 4 plates with different sizes so you should be able to just pick your size and go! It works down to 179mm as i tested for all you BambuLab owners figuring its one of the most popular printers. But Scaling Below 179mm you can get some BAD slices so maybe play with your width/height settings if required.

Settings 

0.28mm Layer height

Seam Back

Sparse infil 5-9%

Enable Support Tree Slim

Brim Auto.

I would also recommend either sanding or trimming the ends before giving to a child!

Happy Printing!!! I just hope someone enjoys this as much as I've hated making it, I'm sure they will I think it looks great. I also don't have any children or children in my close family that could be a witch.  I made this for all of you and your loved ones!!!!  But I have learnt a lot in the process so its up from here!

Tagi