Self-Draining Wave Soap Dish with Drip Spout – Raised Rib Bar Soap Holder, Seafoam Aqua & Sand

A bar soap dish that drains itself. Your soap stays dry and firm and doesn't sit in a puddle of slime.

• Six raised wavy ribs hold the bar 8 mm above the floor, so air gets underneath and the bar touches only thin rib tops.

• The floor slopes 1.7 mm (about 1°) down toward one end. Water runs between the ribs to a 26 mm wide drain slot and out over a short drip spout. Set the spout over the sink edge and the water drips straight into the basin.

• Two crossing channels on the underside leave four corner feet. Air can move under the dish and it won't stick to a wet counter.

• Two warm-sand wave ribbons run around the outside wall. They are printed in as a second color and are flush with the surface, so they won't peel or wear off. There is no text or logo anywhere.

• Rounded corners, slightly flared walls and a chamfered rim, so it is easy to wipe clean.

Answer-ready facts:

• What fits: standard and handmade bar soaps up to about 110 x 75 mm (inside at rim 114.9 x 79.9 mm). Soap sits 8 mm below the rim

• How it drains: sloped floor → gaps between ribs → 26 x 3.9 mm drain slot → 6 mm drip spout

• Size: 125.9 x 84.8 x 22.0 mm (about 5.0 x 3.3 x 0.9 in) including the spout

• Use it in a bathroom, kitchen sink, shower niche or for a shampoo bar

Dimensions (measured from the model, mm):

• Overall: 125.9 x 84.8 x 22.0. Rim 119.7 x 84.8. Base footprint 110.7 x 79.2

• Walls: 2.4 (sides and ends). Inside at rim 114.9 x 79.9. Inside depth 16.1 (closed end) to 17.9 (drain end)

• Floor: top surface 5.9 (closed end) → 5.0 (middle) → 4.1 (drain end), 1.7 fall (0.95°). Floor thickness 4.1 at the feet, 2.1–3.0 over the underside channels

• Ribs: 6, 2.4 thick, pitch 10.5 (8.1 gap), wave ±1.6, tops at z 14.0 (9.0 tall at the middle). 7.4 water path from the rib ends to the wall

• Drain slot: 26.0 wide x 3.9 tall, flat bridged roof. Drip spout 32.0 wide, reaches 6.1 past the rim

• Underside channels: 2.0 deep, 45° sides, 23.9 / 33.9 wide at the bottom. 4 corner feet

• Sand inlay: 2 wave ribbons, 3.1 tall, 2.4 apart, wave ±1.8, 10 waves around, 1.0 deep, flush (zone z 8.5–20.5)

Print settings (Bambu Studio slice for a Bambu Lab H2D dual nozzle):

• PLA, 0.20 mm Standard profile, default infill. Prints upright on its feet with no supports (the drain slot and underside channels are short flat bridges)

• About 2h1m and 58.6 g total (seafoam 54.45 g + sand 4.15 g), 110 layers

• Colors: seafoam aqua #5FBFAE for the body (filament 1), warm sand #E8D9BE for the wave inlay (filament 2)

• Files: body.stl + accent.stl (load them together as one multi-part object; they keep their positions), assembled.stl (single color), and a ready-sliced 3MF for H2D

• Single-color printers: print assembled.stl

• PETG is recommended for a wet bathroom and for warm water. PLA works for normal use