iPad Air Stand – minimal folded stand, portrait and landscape
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A 7 mm strip folded into a hollow triangle. Holds the iPad Air (10.9"/11") portrait and landscape. No supports, ~125 g.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 2
- Wydruki
- 0
- Wyświetlenia
- 13
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Portable Devices
- Licencja
- Creative Commons — Attribution — Share Alike
A minimal desk stand for the iPad Air, designed to look like something Apple could have shipped: one 7 mm strip folded into a hollow triangle, the same idea as a Smart Folio in stand mode or the foot of an iMac. Same wall thickness everywhere, big bend radii, fully rounded sides, nothing to adjust. The iPad drops in with its whole bottom edge resting in the slot and leans back 22°, in portrait or landscape.
Features
Portrait and landscape. The stand is 110 mm wide, narrower than the iPad in either orientation, so the iPad floats over it on both sides and only the bottom edge touches the stand.
Supported along the whole edge. The slot floor is perpendicular to the backrest, so the iPad stands flat on its entire bottom edge instead of on one corner. The 9.5 mm front lip is parallel to the screen and touches the glass over its full height.
Stays put. The flat base is 97 mm deep. It takes a push of about 1.4 N (portrait) or 2.4 N (landscape) on the top edge before it tips, so tapping and swiping is no problem. In practice it is rock solid.
Nothing to hide. No cable channel, no feet pockets, no screws. The underside is one smooth face. If it slides on a very smooth desk, four small self-adhesive silicone bumpers do the trick.
Charging. In landscape the USB-C port is on the side and any cable fits. In portrait the port sits in the slot, so charging in portrait is not possible by design.
Compatibility
Tested with the iPad Air 5th gen (M1, 10.9") without a case.
The iPad Air 4th gen and the 11" iPad Air (M2/M3) have the same dimensions (247.6 × 178.5 × 6.1 mm) and should fit identically.
The slot is 7.1 mm wide (6.1 + 0.5 mm per side). Any tablet up to about 6.5 mm thick will fit; the 11" iPad Pro (5.3 mm) sits a little looser. The 10th gen iPad (7.0 mm) is probably too tight.
Bare iPad only, no case or folio.
Printing
Print the print-on-side STL as oriented, lying on its side. No supports needed: that way every bend prints smooth, there are no overhangs and the layers run along the load. A brim is optional (the contact strip is only 7 mm wide); mine printed fine without.
The upright STL is the same model standing on its base, for anyone who prefers that. Overhangs stay under 35°, but the underside of the rear bend will be rougher.
Printed in PLA, 0.25 mm layers, 2 perimeters, 15% infill: about 125 g and 2 h 45 min on a Prusa CORE One (0.4 nozzle). PETG works just as well.
Model size: 110 × 117 × 95 mm.
Files
STL print-on-side: ready to slice, already lying on its side
STL upright: the same model standing up
STEP: for remixing in your own CAD program
bgcode: ready to print on a Prusa CORE One, 0.4 nozzle, PLA
Credits
Own design, modelled parametrically in FreeCAD with the help of Claude (AI-assisted). Not affiliated with or endorsed by Apple.
Nederlands
Minimalistische bureaustandaard voor de iPad Air (10,9"/11"): één strip van 7 mm, gevouwen tot een holle driehoek, zoals een Smart Folio in standmodus. Staand en liggend, 22° achterover. De iPad rust op zijn hele onderrand in een sleuf van 7,1 mm (zonder hoes). Printen op de zijkant zonder supports en zonder brim, ca. 125 g PLA, ca. 2 uur 45 min. Getest met de iPad Air M1.