Gridfinity-Compatible Starter Kit - Lite or Magnet Baseplates, Stackable Bins, Label Shelf

Everything you need to start a modular drawer or desk system on a Gridfinity-compatible 42 mm grid: baseplates in two sizes and two styles, and a set of stackable bins with a label shelf. Free, with the full parametric source.

Baseplates (measured on the STL files)

• 4 × 4: 168 × 168 mm, fits a 170 mm print bed.

• 2 × 2: 84 × 84 mm.

• Lite: an open frame, 4.65 mm high, fast to print and light.

• Magnet: a 3 mm floor with pockets for 6 × 2 mm magnets (4 per cell), 7.65 mm high.

• Plates put together side by side to fill any drawer.

Bins

• 1 × 1, 2 × 1 and 2 × 2 footprints, in 3 and 6 height units (3 units: 25.4 mm tall with the lip, 6 units: 46.4 mm). The kit has five bins: 1×1×3, 2×1×3, 2×2×3, 1×1×6 and 2×1×6.

• Every bin has the standard foot (0.8 + 1.8 + 2.15 mm) and a stacking lip, so bins of the same size stack on each other.

• Every bin also comes with 6 × 2 mm magnet pockets in the feet (-magnets files) for the magnet baseplate.

• A flat shelf with a 45° underside runs along the inside of the front wall and takes a paper or printed label.

• Walls 1.6 mm, floor 1.2 mm. Bin outer size is 42 n − 0.5 mm, plate size is exactly 42 n.

What is in the pack

• 4 baseplates (4×4 and 2×2, lite and magnet), 5 bins, each bin with and without magnet pockets.

• The parametric .scad source: any size and height, label shelf on or off.

Why it prints well

• No supports: the foot and the stacking lip use 45° chamfers only; the label shelf has a 45° underside; the baseplates print flat.

• All 14 files are closed single solids.

IN THE FILES

• gridfinity_starter-plate-4x4-lite.stl, -plate-4x4-magnet.stl, -plate-2x2-lite.stl, -plate-2x2-magnet.stl

• gridfinity_starter-bin-1x1x3u.stl, -bin-2x1x3u.stl, -bin-2x2x3u.stl, -bin-1x1x6u.stl, -bin-2x1x6u.stl

• the same five bins as -magnets files

• gridfinity_starter.scad

PRINT SETTINGS: PLA or PETG, 0.20 mm layers, 0.4 mm nozzle, 15 % infill, no supports, no AMS needed, one colour per part. Bins: 4 wall lines (the wall is 1.6 mm thick); plates: 3 walls. Print as the files lie, feet or plate bottom on the bed. Solid volumes: 4×4 lite plate 21 cm³, 4×4 magnet plate 100 cm³, a 2×1×3 bin 30 cm³ (up to about 26 g, 124 g and 38 g if printed fully solid in PLA; infill makes them lighter). Glue 6 × 2 mm magnets in with the poles facing to attract.

Honest notes:

• The images are 3D renders made from the same files you print. This model has not been test-printed yet.

• Checked numerically on the exported STLs: a 1 × 1 bin sits in both baseplates without overlap and is held sideways (a 0.4 mm shift makes it touch the pocket); a 2 × 1 bin stacks on another 2 × 1 and is held by the lip; all files have the standard outer sizes.

• We have not fitted these parts to baseplates or bins from other makers, only to the standard profile. Print one bin and one 2 × 2 plate first to check the fit on your printer.

• Gridfinity is an open grid standard; this is an independent, compatible design.

SLICED (Bambu Lab P2S, 0.20 mm, PLA, 3MF included):

• bins-3u: 72.6 g, about 1 h 39 min

• bins-6u: 51.6 g, about 1 h 3 min

• plate-4x4-lite: 22.1 g, about 35 min

• plate-4x4-magnet: 87.6 g, about 2 h 6 min

• plates-2x2: 28.3 g, about 42 min