1 / 6
V8 Muscle Car Convertible 1:18 - Model Kit, Lift-Off Hood, No Supports, No Glue — zdjęcie 1
1 / 6

V8 Muscle Car Convertible 1:18 - Model Kit, Lift-Off Hood, No Supports, No Glue

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

1:18 muscle car convertible kit: lift-off hood, blown V8, full interior. 69 pieces, 6 plates, no supports, no glue.

Ocena
0 / 5
Polubienia
0
Pobrania
2
Wydruki
0
Wyświetlenia
12
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Vehicles
Licencja
Creative Commons — Attribution — Noncommercial

Build your own classic American muscle convertible at 1:18 scale. Every piece prints in one colour on its own plate, without supports, and the whole car pushes together with printed dowels and press fits - no glue, no screws, no magnets. About 274 x 108 x 73 mm, wheelbase 154 mm.

WHAT IS IN THE KIT

  • Lift-off hood: a blue V8 with chrome valve covers and a chrome blower that sticks up through the hood

  • Top down: the folded top sits behind the rear bench, so the interior is on display - bucket seats, rear bench, dashboard with gauges, steering wheel and shifter

  • Separate colour pieces for the details: stripe inlays on the hood and trunk, black grille with 4 headlights, black tail panel with red tail lights, bumpers, windshield frame and twin exhaust tips

  • Five-slot rims in black tyres, wider tyres at the back

  • Radiator at the front of the engine bay, ducktail rear deck, door seams and side scoops

  • The car in the photos has its "chrome" parts printed in green - use silver for the classic look, or any colour you like

  • Red plate: rear body, front clip, hood, 2 tail lights

  • White plate: 2 front seats, rear seat, 4 stripe inlays, 4 headlight lenses

  • Black plate: floor pan, interior tub with dash, folded-top boot

  • Black plate: 4 tyres, grille, tail panel, radiator, steering wheel, column, 24 dowels

  • Silver plate: windshield frame, 2 bumpers, blower, 4 rims, 2 valve covers, 3 axles, 2 exhaust tips, shifter

  • Blue plate: V8 engine block

PRINT SETTINGS

  • The 3MF is ready to print: 6 plates, one colour per plate - no AMS, no filament swaps

  • 0.2 mm layers, 2 walls, 15% gyroid infill, PLA. No supports anywhere

  • Dowels, axles, column and shifter print at 100% infill with a small brim

  • Biggest part is the 232 mm floor pan - every plate fits a 256 x 256 mm bed. Keep the plate clean for the floor pan

  • Every part is already in its print orientation - wheel arches and holes have 45 degree tops, inserts print face up

  • About 400 g in total

ASSEMBLY

  1. Nose: push the 4 headlight lenses into the grille from the back, then press the grille into the nose recess.

  2. Tail: push the 2 red lenses into the tail panel from the back and press the panel into the tail.

  3. Stripes: press the white inlays into the channels on the hood and trunk (hood stripes are thicker at the windshield end).

  4. Floor: push dowels into all 14 holes in the floor pan from the top until they are flush underneath.

  5. Interior: set the tub onto the 2 middle dowels, press the seats onto the rails, push the column into the dash and the steering wheel onto it, shifter into the tunnel.

  6. Rear body onto its 6 dowels, front clip onto its 4 dowels (the joint is the front door seam).

  7. Engine: blue block onto the 2 dowels in the bay, valve covers into the heads, 2 dowels in the valley and the blower on top, radiator into the slots at the front.

  8. Windshield: lay the frame on the cowl and push 2 dowels through it. Folded top: 2 dowels into the well behind the rear seat, press the boot on.

  9. Wheels: press each rim into a tyre (front tyres 14 mm wide, rear 17 mm). Slide the rear axle through, push the front axles into the inner fenders, press the wheels on.

  10. Push the bumpers into the pockets front and rear and the exhaust tips under the rear bumper. Drop the hood in - lift it off any time to show the engine.

GOOD TO KNOW

  • Display model and toy - not for children under 3 (small parts)

  • No glue needed. Too tight? Scrape the crush ribs with a knife or set X-Y hole compensation to +0.05 mm. 4 spare dowels are included.

Original design by Kirimas Studio.

Tagi