MODULITH 270 Wall Mount Starter Kit

Turn your wall into storage.

Screw up a bracket, hang the cases. The bracket goes on the wall with a few wood screws, and the cases hang on it: the screw heads slide into the keyhole slots in the case back and the bracket nests into its back opening. Rows below the top one lock on with QuickLocks, so you can swap or rearrange drawers in seconds.

Three builds, one download. All three layouts use the parts on this page, only the quantities change. Print the 3-drawer build to get started, go straight to the 5-drawer, or put an open shelf above three drawers.

Grow it whenever. Bracket sections install side by side, and more 270 cases hang beneath the top row, so this kit is just the beginning.

GEN2 is now MODULITH. Same system, same compatibility.

PICK YOUR BUILD

2W-2H · 3 drawers · 34 printed pieces in 27 print jobs
176 × 122 × 300 mm (W × H × D, with the bracket and faceplates)
See this exact kit: parts list, filament and print time →
Open its 3D build guide →

3W-2H · 5 drawers · 54 printed pieces in 43 print jobs
264 × 122 × 300 mm (W × H × D, with the bracket and faceplates)
See this exact kit: parts list, filament and print time →
Open its 3D build guide →

2W-5H with shelf · 3 drawers and an open shelf · 39 printed pieces in 31 print jobs
176 × 290 × 300 mm (W × H × D, with the bracket and faceplates)
See this exact kit: parts list, filament and print time →
Open its 3D build guide →

The guide opens in your browser with no sign-up: rotate the build and step through the assembly.

THE 270 COLLECTION

The 270 Collection is the large depth, about 256 mm inside: for long tools, cordless kits and big spools.

WHAT'S IN THE DOWNLOAD

• Wall brackets: Wall Mount Lite, 1W, 2W and 3W, one bracket design for every collection. The 2W-2H and the shelf build use a 2W and the 3W-2H a 3W, and sections install side by side if you grow

• Cases: 270-1W-1H and 270-2W-1H. The Wall Mount Lite bracket needs v2602 or newer cases, which these are

• Covers: 270 Cover Lower and Upper, 1W and 2W, to finish the top row

• Decor Drawers: v2609, 1W-1H and 2W-1H, the drawers the three builds use. They print with a tear-away front: snap it off, or leave it in unless you add a faceplate back cover

• Classic Faceplates: 1W-1H and 2W-1H, each as an STL and a ready-to-slice multi-material 3MF

• Classic Drawers: 1W-1H and 2W-1H, if you would rather print the handle into the drawer

• Shelf parts: the 270-2W-1H Case Extender (the shelf build stacks two on a 270-2W-1H case), the 270-2W Shelf Insert and the 2W Shelf Lip

• Side Covers: 270-1H and 270-3H (the 3H for the shelf), each as an STL and a two-material 3MF, an optional finish for the end walls

• Hardware: QuickLocks (print in PETG), optional drawer stoppers, 10x2mm and 6x2mm magnet inserts

WANT A DIFFERENT FRONT?

The Classic Faceplates in this download are free. Every faceplate series of the same size fits the same Decor drawer, so you can change the look later without reprinting the drawer.

• EdgeLabel: snap-on faces with swappable printable labels. Easy multicolor, even on a single-color printer.

• Classic Pro: the classic look, with swappable labels and accents.

• Chevron: a 45 degree pattern that lines up across every drawer. Takes a separate bolt-on handle and M3 screws.

These three are paid models, each on its own page, and included with the Jerrari Club.

WHAT YOU PRINT

Quantities are prints, not parts. QuickLocks and Drawer Stoppers each come as a left/right pair on one plate, so one print gives you both pieces.

2W-2H · 3 drawers

• 1 × Wall Mount Lite Bracket, 2W section

• 2 × 270-1W-1H Case

• 1 × 270-2W-1H Case

• 2 × Decor Drawer 270-1W-1H

• 1 × Decor Drawer 270-2W-1H

• 2 × Classic Faceplate 1W-1H

• 1 × Classic Faceplate 2W-1H

• 2 × 270 Cover Lower 1W

• 2 × 270 Cover Upper 1W

• 3 × QuickLock A (print in PETG)

• 6 × Magnet Insert (optional, for the magnetic closure)

• 4 × Drawer Stoppers (optional)

• 4 × 270-1H Side Cover (optional finish, not in the printed-piece count)

3W-2H · 5 drawers

• 1 × Wall Mount Lite Bracket, 3W section

• 4 × 270-1W-1H Case

• 1 × 270-2W-1H Case

• 4 × Decor Drawer 270-1W-1H

• 1 × Decor Drawer 270-2W-1H

• 4 × Classic Faceplate 1W-1H

• 1 × Classic Faceplate 2W-1H

• 3 × 270 Cover Lower 1W

• 3 × 270 Cover Upper 1W

• 5 × QuickLock A (print in PETG)

• 10 × Magnet Insert (optional, for the magnetic closure)

• 6 × Drawer Stoppers (optional)

• 4 × 270-1H Side Cover (optional finish, not in the printed-piece count)

2W-5H with shelf · 3 drawers and an open shelf

• 1 × Wall Mount Lite Bracket, 2W section

• 2 × 270-1W-1H Case

• 2 × 270-2W-1H Case

• 2 × 270-2W-1H Case Extender

• 1 × 270-2W Shelf Insert

• 1 × Shelf Lip 2W

• 2 × Decor Drawer 270-1W-1H

• 1 × Decor Drawer 270-2W-1H

• 2 × Classic Faceplate 1W-1H

• 1 × Classic Faceplate 2W-1H

• 2 × 270 Cover Lower 1W

• 2 × 270 Cover Upper 1W

• 6 × QuickLock A (print in PETG)

• 6 × Magnet Insert (optional, for the magnetic closure)

• 2 × Drawer Stoppers (optional)

• 4 × 270-1H Side Cover and 2 × 270-3H Side Cover (optional finish, not in the printed-piece count)

WHAT YOU'LL NEED

• Wood screws: 4 for the 2W-2H and the shelf build, 6 for the 3W-2H, two per 1W. Countersunk #6 or #8. Screw length and anchors depend on your wall: go into a stud wherever you can, use wall anchors in drywall with no stud, and any other wall material needs a fixing made for it.

• Tools: a screwdriver, a drill bit smaller than your screws, and a pen, marker or scratch awl to mark the holes.

• Filament: PLA or PETG.

• Magnets (optional): 6 or 10, 10×2mm or 6×2mm, only if you add the magnetic closure.

• M3 screws (optional): one M3×6mm socket head screw and one M3 hex nut per 1W cover, only to fix the covers in place.

As an Amazon Associate I earn from qualifying purchases.

No load rating is published, so judge what you store in it and check the fixings yourself. Narrow cases go on top because the case walls nearest the support carry hanging weight better; that is design guidance, not a load test. The shelf build is the exception: its shelf hangs on the bracket and carries the drawers below it, and the wide drawer at the bottom ties the two narrow ones together.

LET THE FREE PLANNER HANDLE THE DETAILS

Want a different layout? Build it in the free MODULITH Planner: it works out the parts, hands you a complete parts list with download links, shows it in your own filament colors, and generates a step-by-step 3D assembly guide for your exact setup.

👉 Open the free MODULITH Planner →

INSTRUCTIONS

🔧 Step-by-step wall mount instructions →

🎥 Watch the wall mount video

PRINT SETTINGS

• Recommended filament: PLA, or PETG or ABS for heavier duty storage

• QuickLocks: PETG

• Nozzle: 0.4mm

• Layer height: 0.2-0.35mm

• Infill: 10-20%

• Supports: None

KEEP BUILDING

• 270 Decor Drawers

• 270 Cases

• 270 Side Covers

• Classic Faceplates, free

• Wall Mount Brackets on their own

• 270 Tabletop Starter Kit

SUPPORT MODULITH AND UNLOCK MORE

Join the Jerrari Club for member-exclusive models and early access. Every membership helps fund new MODULITH releases and free tools like the Planner.

NEW TO MODULITH?

🎥 Watch the system overview

UPDATES

2026-11 - First release, with the two official builds and their 3D guides.

2026-11 - A third build: 2W-5H with an open shelf, with its shelf parts and the 270-3H side cover.

This model is licensed CC BY-NC-SA 4.0. The Non-Commercial part refers specifically to selling prints. You're absolutely welcome to use my designs in commercial environments, I actually encourage you to use them anywhere you see fit! 👍