ePaper Case for TRMNL 7.5" DIY Kit with Magnetic Wall Mount and Pole Clamp
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Screwed case for the Seeed TRMNL 7.5" ePaper kit with slide in tray, magnetic wall mount and tool free pole clamp.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 19
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
A sturdy, fully screwed case for the Seeed Studio TRMNL 7.5" (OG) DIY Kit (800 × 480 ePaper, XIAO ePaper driver board with XIAO ESP32 S3 Plus, 2000 mAh battery), plus two holders that share the same magnetic interface: a wall mount and a tool free clamp for 40 mm poles.
The full write up with more photos, renderings, videos, current measurements and the parametric FreeCAD source is on my blog:
Case and wall mount: https://blog.josias.de/en/posts/zimmeranzeige/
Pole clamp: https://blog.josias.de/en/posts/gasanzeigestangenhalter/
The case
Stands on the desk tilted 12° backwards, or hangs on one of the two holders
The electronics sit on a tray that slides in from the front and carries board and battery
Bezel with button caps 1, 2, 3, R and a slider for the power switch, labels printed in a second colour
Everything is held by M2 socket head screws and nuts in nut pockets, nothing is glued, so you can open it at any time
Board dimensions and button positions are taken from the Seeed KiCad data
Alternative plain back cover without magnets if you only want a desk stand
Magnetic holder with detent joint
The back cover has a 64 mm ring with twelve stacks of two 6 × 2 mm magnets and twelve cone sockets, the holder disc has the matching magnets and three centring cones
The display holds very firmly, comes off with one move for charging and can be put on in 30° steps
The joint clicks from 45° down to 45° up in 15° steps. Two Bambu Lab ball spring plungers are offset against each other, so the joint is preloaded in every position and does not rattle
Wall mount: the wall plate is fixed with two strips of mounting tape
Pole clamp: hinged shell with cam lever for tubes with 40 mm diameter, opens and closes without tools. TPU inserts sit in dovetail grooves and grip the tube without scratching it. Behind the tube the shell is only 4.5 mm thick
Note on the pole clamp: it was made for the slanted leg tubes of a large tent, so the saddle includes a 19.5° wedge that keeps the display vertical on a pole tilted by 19.5°. Saddle, shell and lever are fixed solids in the FreeCAD project, so other diameters or angles need some remodelling.
Files
The Bambu Studio project (Gehaeuse_Projekt_ABS-GF.3mf) contains all parts with print settings, arranged on plates:
Always print: front housing, tray, bezel, buttons, slider
Plain back cover (desk stand only)
Back cover with magnets plus wall mount
Back cover with magnets plus pole clamp, TPU inserts printed in place (multi material)
to 7. Pole clamp for printers without a good multi material system, TPU inserts printed separately and pressed in
All STL files are in print orientation. The file names are German:
01_Gehaeuse_Front: front housing
02_Rueckdeckel: back cover with magnetic interface
02b_Rueckdeckel_ohne_Halter: plain back cover
03_Einschub_Blende: bezel (plus lettering as a separate body for the second colour)
04_Einschub_Schlitten: tray
05_Schieber: slider for the power switch
06 to 09 Knopf: button caps 1, 2, 3, R (plus lettering)
10_Halter_Scheibe: holder disc
11_Halter_Gelenk: joint
12_Halter_Arm_Wand: arm with wall plate
12b_Halter_Arm_Stange: arm for the pole clamp
14_Sattel_Keil: saddle with wedge (plus TPU insert)
15_Klappschale: hinged shell (plus TPU insert)
16_Spannhebel_A and 16b_Spannhebel_B: the two cheeks of the cam lever
Printing
I printed everything in black ABS GF with orange lettering on textured PEI at 0.12 mm layer height, the inserts in TPU. Test prints work well in PLA, PETG works too. The case parts print without supports. The pole clamp parts are printed standing on their end face, a few painted on supports can help under the overhanging hinge eyes. A brim is recommended for the front housing.
Hardware
Case with wall mount:
TRMNL 7.5" (OG) DIY Kit from Seeed Studio
Socket head screws (DIN 912): 6 × M2×4, 13 × M2×6, 3 × M2×8, 1 × M2×12
23 × M2 nut
48 × neodymium magnet 6 × 2 mm
2 × Bambu Lab ball spring plunger 5 × 6 mm (FB004)
1 × steel pin 2 × 30 mm
4 × rubber foot 8 × 2 mm (optional, only for standing)
2 strips of mounting tape 20 mm
Additionally for the pole clamp:
4 × M3×10 socket head screw and 4 × M3 nut
1 × M2×12 and 1 × M2 nut
Steel pins 2 × 50 mm (hinge) and 2 × 20 mm (cam lever)
With the plain back cover you need no magnets, ball springs, steel pin or tape.
Assembly
Put nuts into the blocks of the bezel, insert slider and button caps from behind and screw the bezel to the tray with two M2×4.
Place board and battery into the tray, screw down the board and plug in the battery.
Slide the tray in from the front, secure it underneath with two screws and on the right side with one M2×6 through the case wall.
Insert the display, put on the back cover and fix it with nine M2×6 and two M2×8 from the top.
Magnets: all stacks in the back cover with the same pole facing out, all stacks in the holder disc with the opposite pole.
Holder: press in the ball springs, screw the holder disc to the joint with three M2×6, put the tongue into the fork of the arm and press in the 30 mm pin.
Pole clamp: put the M3 nuts into the side slots of the saddle and screw it to the arm with four M3×10. Open the hinged shell by about 90°, slide it into the hinge eyes from the side and press in the 50 mm pin. Place the two cheeks of the cam lever around the centre lug, push the 20 mm pin through and screw cheek B to the grip bar with the M2×12.
More details, firmware examples and the FreeCAD file are in the blog articles linked above.