Curiosity Rover - (A modular, RC like crude model)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A RC like, kind of crude curiosity rover made entirely on fusion 360 with some wiring holes left for wires to flow.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 18
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- RC & Robotics
- Licencja
- Creative Commons — Attribution — Share Alike
RC - CURIOSITY ROVER
This is a RC-like Curiosity Rover model, It has quite some flaws and I admit it but I think it looks kind of good enough to be considered a RC for a first timer like me to do this kind of thing. The rover has 95 parts all put together to make it resemble the OG Curiosity Rover.
FEATURES
Wiring holes left out in sides of shell and in arms for motor fittings.
Top part of shell consist of a bolted hatch like part to cover and access its insides.
All of the motors used in Wheels and arms are made in mind for Doryoku Motors (L: 61mm, D:18mm).
The screws sticking out in the top most and arm's front most part are for gopros or some small cameras with side motor housing for mentioned motor above to act as a drill.
PARTS NAMING
How my parts are named and how can one differentiate.
WHEELS & MOTOR HOUSING
Left (Left side motor holding arms) : <Part name> + L [ L = indicating Left side ]
Sub-arm (Small motor arms attached to the main arm): <Part name> + L [ L = indicating Left side ]
Front (Front indicating non motorized sub arm): <Part name> + LSF (L = side, S = sub arm, F = Front)
PS: SAME NAMING SYSTEM GOES FOR RIGHT SIDE WITH 'R' INSTEAD OF 'L' INDICATING SIDE ( LEFT OR RIGHT)
CAMERA
Holder Rotations: <Part name> (Holds all planetary gear, camera rotators and all)
Camera Lower arm: lower arm of the camera holder
ARM
Front tubings with motor housings to move the tubes, all together forming a arm
Main Joint (AF) : Planetary (Consists of 6 : 1 gearing planetary gear) that moves the first joint. Naming is simply <Part name>.
Second Arm: <Part name> + JTM (JTM are given to parts joined to the main arm, JTM = Joined To Main arm).
Head Rotator: <Part name> + JTS (JTS are given to parts joined to the second arm, JTS = Joined To Second arm).
Head: 2 parts with <Part name> + JTH (JTH = Joined to Head)
DIFFERENTIAL
Joins left and Right side of the arms housing motors and wheels.
BALL BEARING DIFF: Ball bearing of the top of rover shell's differential
Its part naming is simply <Part Name>
ROVER SHELL BACK
Consists of few parts to give the rover a personality and character and is simply <Part Name> nothing fancy
GENERATOR THING
Lid Bolt: consists of 10 bolts holding the generator's lid altogether
Two similar parts: There are many same parts mirriored to the other side and named as <Part Name> + L / R ( L / R: as in if the parts are in left side or right side)
PS: THE SIDES ARE DIFFERENTIED UPON LOOKING THE ROVER FROM ITS ARM FRONT.
PARTS ASSEMBLY INSTRUCTION

First Put in the joint in the Rover shell's Joint hole



2. Put in the fork holder with its parts and screw down the fork parts




Put that inside the joint and lock it down with thread locker


It should look like this

now put in the Rotator gear adapter in the rotator and join with the arm's front bulgy part



put the Motor housing below the rotator and use clamp among them



Put the gear adapter in your wheel and put the motor in the motor housing joining the wheel


Repeat the motor housing thing for the wheel behind it and the Rotator, gear adapter and then motor housing for the wheel on the back most side, it should look like this

Screw down the 'fork holder' part in the differential which should look like this

Repeat the same for other side and it should be like this

NOW, Put in the differential ball bearing and THEN put in the screw on top of that ball bearing




NOW for camera module, Put in the lower arm tube into the rover's shell's cylinder sticking out part


Put the planetary gear with threads on top of that lower arm tube


Now put in the gearbox lid on and then the camera holder in the thread and then put in the right mouth plate piece with gear and the left and motor gear with motor attached to it

Put in the planetary gear in front of the arm holder (6:1) ratio planetary gear with rectangular shaft


Put in the rotator main joint and then the rotator cuff with m11 x 1 bolts on the rotator cuffs

Put in the motor housing in first and then the rotator joint pin for this

PUT IN THE 61mm long motor and then put in the motor lip in front of it and then screw it down and then put the gear adapter in its shaft

Put in the long 'L' Shaped arm in it

Put in the gear then the lip and then the adapter and Voila, you have second arm

do the same thing for the second arm and then put in the head arm which should look like this at the end

Lets go to the back of the rover, Put in the triangle things and then bolt them down and voila you should have this

Put in the heat exchanging plates with its support bracket rod in place of the notches made in the back fins

Since you're already there, here's a puzzle for the generator support brackets enjoy :))

Now put in the back plate and THEN VOILA, you're not there yet

Put in the rover cover and then bolt it down when you need to close it

There you have it, Enjoy!!